mark : Standard stocked item
mark:
To be replaced by a new item featured on the same page
mark: To be replaced by new item
(Please confirm stock availability)
* mark:
Semi-standard stock (Please confirm stock availability)
mark:
Stock or planned stock (Please confirm stock availability)
No mark: Made-to-order item
mark: We cannot produce
Stock Indications and Symbols
E1
SEC-Boring Bar Series .................................................................... E2
Boring Bar Identification .................................................................. E4
Boring Bar Selection Guide ............................................................ E5
Multifunctional Small Tool Twin Headed Holders ....................... E10
Bottom
Facing
SEC-Boring Bars
Expanded
Expanded
Expanded
S-SCLC Type / A-SCLC Type .................................................. E12
B-SCLC Type / C-SCLC Type .......................................................... E13
E-SCLC Type .................................................................................... E14
S-SCLP Type / A-SCLP Type ................................................... E19
B-SCLP Type / D-SCLP Type / C-SCLP Type ................................ E20
S-DCLN Type / D-DCLN Type ......................................................... E23
S-PCLN Type / B-PCLN Type .......................................................... E24
S-ECLN Type /
Expanded
S-DWLN Type .................................................E25
D-DWLN Type /
Expanded
S-PWLN Type ................................................E26
Profiling
SEC-Boring Bars
Holders for Aluminum Foil Machining
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
S-SDUC Type / A-SDUC Type .................................................E27
B-SDUC Type / C-SDUC Type ......................................................... E28
S-SDQC Type / A-SDQC Type ................................................. E29
B-SDQC Type /
Expanded
S-SDZC Type .................................................. E30
S-DDQN Type /
Expanded
S-DDUN Type / D-DDUN Type ...................... E35
S-PDUN Type / S-EDUN Type ......................................................... E36
S-PDZN Type / S-EDZN Type / S-DTR55C Type ........................... E37
S-SVJB Type / B-SVJB Type / S-SVJC Type ................................. E38
S-SVQB Type / B-SVQB Type / C-SVQB Type............................... E39
S-SVQC Type / A-SVQC Type .................................................. E40
S-SVUB Type / B-SVUB Type / C-SVUB Type ............................... E41
S-SVUC Type / A-SVUC Type .................................................. E42
S-SVZB Type / B-SVZB Type / C-SVZB Type ................................E43
S-SVZC Type ....................................................................................E44
MV Type / GD Type .............................................................. (C36 C37)
Through
Boring
SEC-Boring Bars
Expanded
Expanded
S-SSKP Type / C-SSKP Type .......................................................... E49
S-CSKP Type .................................................................................... E50
S-SSKC Type .................................................................................... E52
S-DSKN Type /
Expanded
S-PSKN Type .................................................. E53
S-ESKN Type / S-PSYN Type / S-ESYN Type ................................ E54
S-SWUB Type / C-SWUB Type .......................................................E55
S-SWUP Type ................................................................................... E57
Stop Boring
SEC-Boring Bars
Expanded
Expanded
S-STUB Type / S-STUP Type / A-STUP Type ........................ E58
B-STUP Type / D-STUP Type .......................................................... E59
C-STUB Type / C-STUP Type / E-STUP Type ................................ E60
S-CTFP Type ..................................................................................... E66
S-DTFN Type / D-DTFN Type .......................................................... E68
S-PTFN Type / B-PTFN Type ..........................................................E69
S-ETFN Type ..................................................................................... E70
Minimum Boring
Small Boring
SEC-Very Small Hole Boring Bars
Carbide Solid Bars
SUMIBORON Small Diameter Boring Bars
SUMIDIA Small Hole Boring Bars
Expanded
Expanded
CKB Type .......................................................................................... E71
BXBR Type ....................................................................................... E75
BSME Type ....................................................................................... E76
SEXC Type ....................................................................................... E77
BNBX Type / BNB Type ................................................................... E78
BNZ Type ........................................................................................... E79
DABB Type ........................................................................................ E80
For Double Clamp Holders Clamp Set Parts .............................................................................. E81
E
Boring
Bars
E1 –E81 E
Boring Bars
E
Boring
Bars
E2
E
SEC-
Boring Bar Series
Complete Support For Boring Operations For Turning
Tooling Selection Guide
S-ECLN
(BCLN)
E25
S-DCLN
E23
D-DCLN
E23
S-PCLN
E24
B-PCLN
E24
BNZ
E79
S-EDUN
(BDUN)
E36
S-EDZN
(BDZN)
E37
S-DDUN
S-DDQN
E35
E35
D-DDUN
E35
S-PDUN
E36
S-PDZN
E37
S-DTR55C
T-REX
E37
B-SCLP/D-SCLP*
XBPC/XBPC-H)
E20
C-SCLP
(WBPC)
E20
B-SCLC
E13
A-SCLP
E19
A-SCLC
E12
C-SCLC
E-SCLC*
E13
E14
(
S-SCLP
(BBPC)
E19
S-SCLC
E12
S-SDUC
S-SDQC
E27
E29
B-SDUC
B-SDQC
E28
E30
S-SVUC
S-SVUB
E42
E41
B-SVUB
B-SVQB
E41
E39
C-SVUB
C-SVQB
E41
E39
S-SVQC
S-SVQB
E40
E39
S-SVZC
S-SVZB
E44
E43
S-SDZC
E30
B-SVZB
E43
C-SVZB
E43
C-SDUC
E28
A-SDUC
A-SDQC
E27
E29
A-SVUC
A-SVQC
E42
E40
Applications
Bottom Facing
Insert shape
Construction / Shank material
C
80˚ Diamond Type
* mark: With oil hole The type codes in ( ) are old type codes.
Screw LockLever Lock
Pin Lock Top Clamp / Double Clamp
Steel shank
Carbide shank
Carbide shank
Carbide shank
Steel shank Steel shank
Vibration
control shank
Steel shank
Vibration
control shank
Vibration
control shank
Profiling Back Turning
V
35˚ Diamond
Type
V
35˚ Diamond Type
D
55˚ Diamond
Type
D
55˚ Diamond
Type
Special Type
Double Clamp
T-REX Holders
CBN
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Boring
Bars
E3
E
SEC-
Boring Bar Series
Tooling Selection Guide
S-ESKN/S-ESYN
(BSKN/BSYN)
E54
BXBR
E75
BSME
E76
BNBX BNB
E78E78
SEXC
E77
S-PSKN
S-PSYN
E53
E54
S-DSKN
E53
S-CSKP
E50
S-ETFN
(BTFN)
E70
CKB
E71
D-DWLN
E26
S-PWLN
E26
S-DTFN
E69
S-CTFP
E66
D-DTFN
E69
S-PTFN
E68
B-PTFN
E68
S-DWLN
E25
C-SWUB
(WBPW)
E55
C-SSKP
(WBPS)
E49
S-SWUB
S-SWUP S-SSKP
(BBPS)
S-SSKC
E55
E57
E49
E50
(BBPW)
S-SVJB /S-SVJC
E38
B-SVJB
E38
B-STUP/D-STUP*
(XBPT/XBPT-H)
C-STUP/C-STUB
(WBPW)
E60
S-STUP/S-STUB
(BBPC)
E58
C-SWUB
(WBPW)
E55
S-SWUB
(BBPW)
S-SWUP
E55
E57
E59
A-STUP
E58
E-STUP
*
(WBPT-H)
E60
Applications
Through Hole Boring
Insert shape
Construction / Shank material
W
Trigon
/Others
S
Square
* mark: With oil hole The type codes in ( ) are old type codes.
Screw LockLever LockPin Lock Top Clamp / Double Clamp
Carbide shankCarbide shank
Steel shank Steel shank
Vibration
control shank
Steel shank
Vibration
control shank
Vibration
control shank
Steel shank
Interior Sphere
Bottom Facing
V
35˚ Diamond
Type
Blind Hole Boring
T
Triangular Type / Others
Carbide shank
Solid
Carbide shank
W
Trigon
/ Others
CBN
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Expanded
Boring
Bars
E4
E
SEC-
Boring Bar Identification
Shank
material
Chart 1
(Chart 5)
Insert shape
Symbol
Insert shape
Symbol
Insert shape
AParallelogram
85 angle
85° MDiamond
86 angle
86°
BParallelogram
82 angle
82° OOctagonal
CDiamond
80 angle
80° PPentagonal
DDiamond
55 angle
55° RRound
EDiamond
75 angle
75° SSquare
FDiamond
50 angle
50° TTriangle
HHexagonal VDiamond
35 angle
35°
KParallelogram
55 angle
55° WTrigon 80°
LRectangular
(Chart 6)
Holder style (The part marked with -- indicates the main cutting edge)
Symbol
Shape Offset
Symbol
Shape Offset
A90° No N63° No
B75° No Q107.5° Yes
D45° No R75°
Yes
E60° No S45°
Yes
F90° Yes T60°
Yes
G90° Yes U93° Yes
J93° Yes W60° Yes
K75° Yes Y85° Yes
L95° Yes Z93° Yes
(Chart 1)
Shank material
SSteel shank
ASteel shank with oil hole
BSteel shank with vibration
control mechanism
DSteel shank with oil hole and
vibration control mechanism
CCarbide shank
E
Carbide shank with oil hole
(Chart 4)
Clamping system
Symbol
Clamp type
Mechanism example
Symbol
Clamp type
Mechanism example
CTop Clamp M
Top Clamp
Pin Lock
DDouble Clamp P
Lever Lock
(Two-side
constrained)
E
+ Pin Lock
(supported by 1 lathe)
SScrew Lock
(Chart 8)
Feed direction
Symbol
Right hand
Symbol
Left hand
RL
SEC-Boring Bar Identification (Round Shanks) [ISO Standard]
Shank length
Chart 3
Shank
diameter
mm
Clamping
system
Chart 4
Holder style
Chart 6
Insert shape
Chart 5
Relief angle
Chart 7
Insert cutting
edge length
mm
Minimum
bore diameter
mm
Feed direction
Chart 8
Insert
thickness
mm
* These symbols may be omitted depending on the product.
(Example)
S16R STUPR1103-18
*
*
(Chart 3)
Shank length
Symbol
Length (mm)
Symbol
Length (mm)
Symbol
Length (mm)
F 80 M 150 T 300
G 90 N 160 U 350
H 100 P 170 V 400
J 110 Q 180 W 450
K125 R200
L 140 S 250
(Chart 7)
Relief angle
Symbol
Relief angle
A3
B5
C7
D15
E20
F25
G30
N0
P11
OSpecial relief angle
BB Steel shank boring bar
WB Carbide boring bar
XB
Steel shank boring bar with anti-vibration control mechanism
PPositive Inserts
Symbol TSC
Insert shape Triangle Square
80 diamond type
Symbol 562034
Insert inscribed circle (mm)
3.97 4.76 6.35 7.94 9.525 12.70
Symbol 08 10 12 16 20 25
Shank diameter (mm)
81012162025
Symbol RL
Feed direction
Right Left
With oil hole Minimum bore
diameter
SEC-Boring Bar Identification (Round Shanks) [Sumitomo Standard]
(Example) WB P T 212R H14
Boring
Bars
E5
E
Boring Bar Selection Guide
Selection Guide By Application / Process
Colored sections: manufacturable sizes (without oil hole) : In stock H: With oil hole in stock
Application
Tool type
Shank type boring
depth (L/D)
Applicable
inserts
type/shape
Tooling
Minimum bore diameter (mm)
Note: If different from the machineable diameter in the heading, it is indicated in the table
Steel
Carbide
Vibration
control
1
1.5
2345678
10 12 13 14 16 18 20 22 25 28 34 44 54 70
Minimum Boring
CKB
E71
–3
Coated carbide,
SUMIDIA
specialized insert
BXBR
E75
–5 Coated carbide 2.0–5.0
Every 0.5
DABB
E80
–2 Brazed
SUMIDIA
Stop Boring
BSME
Expanded
E76
–4 Brazed
SUMIBORON
H
2.5–5.0
Every 0.5
SEXC
Expanded
E77
–3 SUMIBORON
Specialized insert H H H
BNBX
E78
–5 Brazed
SUMIBORON 2.5–8.5
Every 0.5
BNB
E78
–4
SUMIBORON
specialized insert
S-STUB/
S-STUP
[
BBPT
]
E58
–3
Triangle
5 positive
(with hole)
11 positive
(with hole)
A-STUP
E58
–3 H H H H H H
B-STUP/
D-STUP
[XBPT/XBPT-H]
E59
–6
H H H 40
C-STUP B /
E-STUP
[WBPT/WBPT-H]
E60
–8
H H H H H H
S-CTFP
E66
–3 Triangle
11 positive
(without hole) 32
S-PTFN
Expanded
E69
–3 40 50 63
B-PTFN
E69
–6
32 40 50
S-DTFN
E68
–3
40 50 63
D-DTFN
Expanded
E68
–6 H
32
H
40
H
50
S-ETFN
BTFN E70
–3
Triangle
negative (with hole)
Bottom Facing
BNZ
E79
–5
SUMIBORON
specialized insert
911 17 21
S-SCLC
Expanded
E12
–3
80 diamond type
7 positive (with hole)
27 32
A-SCLC
E12
–3 H H H H H H
27
B-SCLC
E13
–6
32
The type codes in [ ] are old type codes. 1
1.5
2345678
10 12 13 14 16 18 20 22 25 28 34 44 54 70
Boring
Bars
E6
E
Colored sections: manufacturable sizes (without oil hole) : In stock H: With oil hole in stock
Application
Tool type
Shank type boring
depth (L/D)
Applicable
inserts
type/shape
Tooling
Minimum bore diameter (mm)
Note:
If different from the machineable diameter in the heading, it is indicated in the table
Steel
Carbide
Vibration
control
1
1.5
2345678
10 12 13 14 16 18 20 22 25 28 34 44 54 70
Bottom Facing
C-SCLC
E13
–8
80 diamond type
7 positive (with hole)
E-SCLC
E14
–8
With
oil hole
H H H H
S-SCLP
[BBPC] E19
–3
80 diamond type
11 positive
(with hole)
A-SCLP
E19
–3 H H H H H H
27
B-SCLP/
D-SCLP
[XBPC/XBPC-H]
E20
–6
H H H
C-SCLP
[WBPC] E20
–8
S-DCLN
Expanded
E23
–3
80 diamond type
negative (with hole)
DCLN Type
PCLN Type / ECLN Type
32
40 50 63
D-DCLN
E23
–6 H
32
H
40
H
50
S-PCLN
Expanded
E24
–3
32
40 50 63
B-PCLN
E24
–6
40 50
S-ECLN
[BCLN] E25
–3
26
D-DWLN
E26
–6
Trigon t yp e
negative (with hole)
H
32
H
40
H
50
S-DWLN
Expanded
E25
–3
32 40 50 63
S-PWLN
Expanded
E26
–3
40 50
Boring Bar Selection Guide
68
10 12 13 14 16 18 20 22 25 28 32 34 35 40 44 50 54 63 70
Profiling
S-SDUC
Expanded
S-SDQC
Expanded
E27 E29
–3
55 diamond
7 positive (with hole)
SDUC Type
SDQC Type
23
A-SDUC
A-SDQC
E27 E29
–3 H H H
H
23 H
B-SDUC
B-SDQC
E28 E30
–6
C-SDUC
E28
–8
S-SDZC
Expanded
E30
–3 23
S-SVJB
Expanded
E38
–3
30
B-SVJB
E38
–6
30
S-SVJC
E38
–3
S-SVQC
Expanded
S-SVUC
Expanded
E40 E42
–3
SVU Type / SVQ Type
A-SVUC
E42
–3 H H H H
A-SVQC
E40
–3 H H H H
S-SVQB
Expanded
S-SVUB
Expanded
E39 E41
–3
35 diamond type
5 positive (with hole)
7 positive (with hole)
The type codes in [ ] are old type codes. 68
10 12 13 14 16 18 20 22 25 28 32 34 35 40 44 50 54 63 70
H
Boring
Bars
E7
E
Boring Bar Selection Guide
Colored sections: manufacturable sizes (without oil hole) D: In stock H: with oil hole in stock
Application
Tool type
Shank type boring
depth (L/D)
Applicable
inserts
type/shape
Tooling
Minimum bore diameter (mm)
Steel
Carbide
Vibration
control
68
10 12 13 14 16 18 20 22 25 28 32 34 35 40 44 50 54 63 70
Profiling
B-SVQB
B-SVUB
E39 E41
–6
SVU Type / SVQ
Type
C-SVQB
C-SVUB
E39 E41
–8
S-SVZB
Expanded
E43
–3
S-SVZC
Expanded
E44
–3
B-SVZB
E43
–6
C-SVZB
E43
–8
35 diamond type
5 positive (with hole)
7 positive (with hole)
S-DDQN
E35
–3
55 diamond
negative (with hole)
S-DDUN
E35
–3
D-DDUN
Expanded
E35
–6 H H
S-PDUN
Expanded
E36
–3
S-EDUN
[BDUN] E36
–3
S-PDZN
Expanded
E37
–3
S-EDZN
[BDZN] E37
–3
S-DTR55C
E37
–3
Specialized T-REX insert
Through Boring
S-SWUB
[BBPW] E55
–3
Trigon t yp e
5 positive (with hole)
11 positive (with hole)
5.5
C-SWUB
[WBPW] E55
–8
5.5
S-SWUP
Expanded
E57
–3
S-SSKP
[BBPS] E49
–3
Square
11 positive (with hole)
C-SSKP
[WBPS] E49
–8
S-SSKC
E52
–3
Square
7 positive
(with hole)
S-CSKP
E50
–3
Square
11 positive
(without hole)
S-DSKN
Expanded
E53
–3
Square
negative (with hole)
S-PSKN
Expanded
E53
–3
S-PSYN
E54
–3
S-ESKN
[BSKN] E54
–3
S-ESYN
[BSYN] E54
–3
The type codes in [ ] are old type codes. 68
10 12 13 14 16 18 20 22 25 28 32 34 35 40 44 50 54 63 70
Boring
Bars
E8
E
General Feature
The SEC-Boring Bar Series is a collection of SEC-Small
Diameter Boring Bars, a product we began selling in
1976 which continues to be popular today, steel/carbide
shank holders with a highly rigid head design, SumiTurn
X Bar which includes a vibration control mechanism, and
optimized insert grades and chipbreakers.
Complete Support For Boring Operations For Turning
Assists evacuation of chips
Evacuation of
long chips
High rigidity rib
New head design
Strong cross-section
withstands high cutting forces
Evacuation of
short chips
Flattened weight vibrates with
opposite phase from the chatter
and dramatically reduces chatter!
X bar cross section
Direction to
which vibration
generates
during cutting
New vibration control mechanism X
Effective Chattering Killer System
Characteristics
Steel Shank Type
With Vibration
Control Mechanism
Compatible with a wide variety of tooling
Stop boring / bottom facing / through boring / profiling
Minimum machineable diameter: CKB model ø 1 mm–, C-SCLC model ø 5mm–
Vibration control boring bar, SumiTurn X Bar
Carbide short shank is compatible with turret lathes even without cutting (C15M-STUP model,
C20M-STUP model)
Insert grades and chipbreakers compatible with a wide variety of work materials
Dramatically improved chatter resistance, especially effective for rough machining of deep holes
Achieves low cost machining for large diameters/deep holes, shank diameters up to ø32 mm
are in stock
High chip evacuation performance, evacuates chips with double chip pocket
Types with oil hole are in stock
Holders for negative inserts (shank diameter ø25–ø50 mm) are in stock
SEC-
Boring Bar Series
Shank Material Selection
Steel shank
Steel shank with vibration
control mechanism
Carbide shank
General
steel
Shallow hole
(L/D 3)
Economical
High speed
machining
Deep hole
(L/D 3)
Economical
High efficiency machining
with wiper insert
Hardened steel/
hardened steel machining
High-precision
machining
: 1st recommendation : 2nd recommendation
Machining method
Bar type
Vibration control may not work correctly if the area near
the label is clamped (due to containing
the vibration control mechanism).
Therefore, the minimum protrusion length is set at 3.5 D
(3.5 times shank diameter).
Label
attachment area
Steel Shanks With Vibration Control
Mechanism, Clamp Position Precaution
Boring
Bars
E9
E
SEC-
Boring Bar Series
Grade Recommendations
Chipbreaker Recommendations
: 1st recommendation : 2nd recommendation
25201612108324050
0
1
2
3
4
5
6
7
8
Shank diameter (mm)
Protrusion length / Shank diameter (L/D)
Carbide shank
X bar
(Positive insert)
Steel shank
X bar
(Negative insert)
Cutting speed: Vc = 20–200 m/min
Depth Of cut: ap = 0.1–2.0 mm
Feed rate f = 0.1–0.3 mm/rev
Note: The actual amount of protrusion able to be machined
depends on the work material, tool condition, and
cutting conditions, etc.
Achieves deep hole machining of L/D = 6 for machining diameters
greater than ø32 mm. Negative chip design reduces corner cost.
With different combinations of a large selection of chip breakers,
handles a wide variety of process, from rough cutting to finishing.
0 50 100 150
0.02
0.04
0.06
Cutting time (min)
External oil
supply method
Dry
Internal oil supply method
Work material: SCM435 Inserts: FX breaker (Grade AC510U)
Cutting conditions: V
c
= 150 m/min, f = 0.1 mm/rev, a
p
= 0.3 mm
Average wear on relief side (mm)
Recommended Application Range By Shank Type Comparison Of Wear
By Oil Supply Method
CVD
PVD
High precision Finishing–Light cutting Medium cutting
Insert grade category
Application range Work material
Coated carbide
Cermet
Coated cermet
Carbide
CBN
(SUMIBORON)
PCD
SUMIDIA
General
steel
Stainless
steel
Cast
iron
Heat
resistant
alloy
Hardened
steel
Non-
ferrous
metal
Carbide
S
DA150
BNC2020
T3000Z
AC530U
AC6040M
AC520U
AC510U
ACZ150
AC420K
AC415K
AC405K
AC6030M
AC830P
AC820P
AC810P
T1500A/T1500Z
BNC2010
BN7500
BN7000
BN2000
DA1000
BN1000
G10E
PMKNH
T1000A
AC6020M
AC8025P
AC1030U
: 1st recommendation : 2nd recommendation
M Class: Finishing to Light Cutting
M Class: Light-Medium Cutting
G Class With Ground Chipbreaker
G Class: Chipbreaker
0.2 0.4
0
2
4
SI Type
FC Type
SC Type
Feed rate (mm/rev)
Depth of cut (mm)
0.2 0.4
0
2
4
FX Type SDW Type
FY Type
SD Type
Feed rate (mm/rev)
W Type
FYS Type
FYS Type
Depth of cut (mm)
0.2 0.4
0
SU Type
2
4
SF Type
US Type
Feed rate (mm/rev)
Depth of cut (mm)
MU Type
0.2 0.4
0
2
4
FK Type
LUW Type
LU Type
Feed rate (mm/rev)
Depth of cut (mm)
Boring
Bars
E10
E
Holders (ID boring depth 11.0mm type)
Cat. No. Stock
Diameter
Height Length Head
Depth of cut
Head Maximum
work
diameter* ID Boring Inserts OD Turning Insert
DCON H LF LH CDX LH2
S1588X-CKBE-11 15.875 15 130 32 11 15 12.0
KBMX R 11-
KBMX R 11- T DC 0702
S16X-CKBE-11 16 15 130 32 11 15 12.0
S1905X-CKBE-11 19.05 17 130 32 11 15 12.0
S20X-CKBE-11 20 18 130 32 11 15 12.0
S22X-CKBE-11 22 20 130 32 11 15 12.0
* For internal machining
Holders (ID boring depth 6.0mm type)
Cat. No. Stock
Diameter
Height Length Head
Depth of cut
Head Maximum
work
diameter* ID Boring Inserts OD Turning Insert
DCON H LF LH CDX LH2
S1588X-CKBE-06 15.875 15 130 27 6 10 12.0
KBMX R 06-
KBMX R 06- T DC 0702
S16X-CKBE-06 16 15 130 27 6 10 12.0
S1905X-CKBE-06 19.05 17 130 27 6 10 12.0
S20X-CKBE-06 20 18 130 27 6 10 12.0
S22X-CKBE-06 22 20 130 27 6 10 12.0
* For internal machining
Feature
Advantages of Twin Head Holders
Traditional tools
First process
(external)
Second process
(internal)
Two different tools are required for the two types of processes
Twin head holders
First process
(external)
Second process
(internal)
A single tool is capable of performing two different types of proceesses
Twin head holder shortens the time required for moving the tool post
8
10
E3
13
0°
0°
CDX
LH2
LH H
DCON
LF
CKBE Type
Please refer to page E74 for the value of E3
Multifunctional Small Tools
Twin Head Holders
Dimensions (mm)
Dimensions (mm)
Capable of handling two different types of machining
with a single holder, able to install one additional tool in
the drill sleeve tool post.
External machining using the drill sleeve is possible
Two types in standard stock: internal + external, and
internal + internal
Difference between the cutting edge center heights of
the two tools is less than 40 μm, handles high precision
machining
Boring + External turning
ID Boring Insert
E74
OD Turning Insert
D20–D23
TWIN HEAD
Boring
Bars
E
E11
Holders
Cat. No. Stock Diameter Height Length Head Cutting edge
distance
Depth of cut
Inserts for internal machining
Inserts for face grooving
DCON H LF LH WF CDX
S1588X-CKBB-F 15.875 15 130 32 11. 0 11
KBMX R -
KBMX R - T KBMF R - 05
S16X-CKBB-F 16 15 130 32 11.0 11
S1905X-CKBB-F 19.05 17 130 32 11. 0 11
S20X-CKBB-F 20 18 130 32 11.0 11
S22X-CKBB-F 22 20 130 32 11. 0 11
Note:
LF, WF, and CDX dimensions above refer to when KBMXR0311- (T) is installed. (Dimensions for when other inserts are installed are shown in the table below)
Offset
Depth of cut
Cutting edge
distance Length
Cat. No. E3 CDX WF LF
KBMX R0103- T0.2 3 10.9 122
KBMX R01506- T0.25 6 10.95 125
KBMX R0206- T0.25 6 10.95 125
KBMX R0311- T 0.3 11 11.0 130
KBMX R0411- T 0.5 11 11.2 130
KBMX R0511- T0.7 11 11.4 130
KBMX R0420- T0.5 20 11.2 139
KBMX R0520- T0.7 20 11.4 139
Cutting edge
distance
Cutting edge
distance
Width of cut
Cat. No. WF WF2 CW
KBMF R0615-05 10.9 18.8 1.5
KBMF R0620-05 10.9 17.8 2.0
KBMF R0630-05 10.9 15.8 3.0
We manufacture tools with designs appropriate for various work shapes and process details, such as center holes, facing, external undercutting, etc.
Internal + External
(Angled Holder Design)
Internal + Center Drill Internal + Internal
(Parallel Design)
Insert Cat. No. : KBM XR (Internal + Internal) Type
Insert Cat. No. : KBM FR (Face + Face) Type
CKBB Type
DCON
LH
LF
H
CDX
E3
WF WF
E3
WF WF
CDX
LF
4.3
LF=123.3
WF
WF2
WF
0.2
CW
Multifunctional Small Tools
Twin Head Holders
Insert List E74
Spare Parts
For KBM R insert attachment For DC insert attachment
Clamp Double screw Wrench Screw Wrench
CKBW16 WB4-8 LH020
BFTX02506N
1.5 TRX08
(For Torx holes)
Dimensions (mm)
Special Holder Configurations
Boring Face Grooving
Recommended tightening torque (N·m)
Boring
Bars
E12
E
Bottom Facing
S-SCLC
Steel
Fig 1 Fig 2
95°
0°
DCON
GAMF LF
LH
WF
H
DMIN Min.
machinable diameter
95°
DCON
DMIN Min.
machinable diameter
0°
GAMF
LF
LH
WF
H
Finish-Medium Cut
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Conventional
Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Fig
Applicable inserts
Screws
Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Steel
S08H-SCLC R/L03X1-05
587100
2.5
24
15
1
CC 03X1
BFTX016033
0.2
TRX06
S08H-SCLC R/L03X1-06
687100
3.0
28
13
S08H-SCLC R/L04X1-07
787100
3.5
32
13
1
CC 04X1
BFTX0203N
0.5
S08H-SCLC R/L04X1-08
887100
4.0
37
11
S08H-SCLC R/L0602-10
S08H-SCLC R/L06
10 87100
5.5
19
13
2
CC 0602
BFTX02505N
1. 1
TRX08
S10K-SCLC R/L0602-12
S10K-SCLC R/L06-12
12 10 9 125
6.0
21
12
BFTX02506N
1. 5
S10K-SCLC R/L0602-13
S10K-SCLC R/L06
13 10 9 125
7. 0
21
12
S12M-SCLC R/L0602-14
S12M-SCLC R/L06-14
14 12 11 150
7. 0
25
10
S12M-SCLC R/L0602-16
S12M-SCLC R/L06
16 12 11 150
9.0
25
10
S16R-SCLC R/L0602-18
18 16 15 200
9.0
27
8
S16R-SCLC R/L09T3-18
18 16 15 200
9.0
30
10
2
CC 09T3
BFTX0407N
3.0 TRX15
S16R-SCLC R/L09T3-20
S16R-SCLC R/L09
20 16 15 200
11. 0
30
8
S20S-SCLC R/L09T3-22
22 20 18 250
11. 0
30
8
BFTX0409N
3.4 TRX15
S20S-SCLC R/L09T3-25
S20S-SCLC R/L09
25 20 18 250
13.0
30
7
S25T-SCLC R/L09T3-27
27 25 23 300
13.5
35
6
S25T-SCLC R/L1204-32
S25T-SCLC R/L12
32 25 23 300
17.0
38
6
2
CC 1204
BFTX0511N
5.0 TRX20
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Steel with oil hole
A08H-SCLC R/L0602-10
10 87100
5.5
19
13
CC 0602
BFTX02505N
1. 1
TRX08
A10K-SCLC R/L0602-12
12 10 9 125
6.0
21
12
BFTX02506N
1. 5
A12M-SCLC R/L0602-14
14 12 11 150
7. 0
25
10
A16R-SCLC R/L0602-18
18 16 15 200
9.0
27
8
A16R-SCLC R/L09T3-18
18 16 15 200
9.0
30
10
CC 09T3
BFTX0407N
3.0
TRX15
A20S-SCLC R/L09T3-22
22 20 18 250
11. 0
30
8
BFTX0409N
3.4
A25T-SCLC R/L09T3-27
27 25 23 300
13.5
35
6
A-SCLC
Bottom Facing
Steel
Oil hole
95°
(For Torx holes)
(For Torx holes)
Recommended tightning torque (N m) mark: Standard stocked item (expanded product) mark: To be replaced by a new item, shifted to made-to-order production, discondinued, etc. (Confirm the stock availability.)
SEC-Boring Bars
S-SCLC Type / A-SCLC Type
Dimensions (mm)
GAMF
WF
95°
LF
LH
H
DCON
0°
DMIN Min.
machinable diameter
With oil hole
Dimensions (mm)
This figure shows right handed tools.
This figure shows right handed tools.
Boring
Bars
E13
E
95°
DCON
GAMF LF
WF
H
DMIN Min.
machinable diameter
Fig 1
95°
0°
Fig 2
DCON
DMIN Min.
machinable diameter
GAMF
LF
LH
WF
H
Finish-Medium Cut
SEC-Boring Bars
B-SCLC Type / C-SCLC Type
95°
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Holder
Material
Cat. No. Conventional Cat.
No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Fig Applicable inserts Screws
Wrenches
R
DMIN
DCON
HLF
WF
LH
GAMF
Carbide
C04G-SCLC R03X1-05 C04G-SCLC R03X1-05
54
3.8
90
2.5 15
1CC 03X1
BFTX016033
0.2 TRX06
C05H-SCLC R03X1-06 C05H-SCLC R03X1-06
65
4.4
100
3.0 13
C06J-SCLC R04X1-07 C06J-SCLC R04X1-07
76
5.4
110
3.5 13
1CC 04X1
BFTX0203N
0.5 TRX06
C07K-SCLC R04X1-08 C07K-SCLC R04X1-08
87
6.4
125
4.0 11
C08H-SCLC R0602-10 C08H-SCLC R06
10 8
7. 0
100
5.5
19
13
2CC 0602
BFTX02505N
1. 1
TRX08
C10K-SCLC R0602-12 C10K-SCLC R06-12
12 10
9.0
125
6.0
21
12
BFTX02506N
1. 5
C10K-SCLC R0602-13 C10K-SCLC R06
13 10
9.0
125
7. 0
21
12
C12M-SCLC R0602-14 C12M-SCLC R06-14
14 12
11. 0
150
7. 0
25
10
C12M-SCLC R0602-16 C12M-SCLC R06
16 12
11. 0
150
9.0
25
10
C16R-SCLC R09T3-20 C16R-SCLC R09
20 16
15.0
200
11. 0
30
8
2CC 09T3
BFTX0407N
3.4 TRX15
C20S-SCLC R09T3-25 C20S-SCLC R09
25 20
18.0
250
13.0
35
7
BFTX0409N
3.4
ø16 DCB
15 100
Sleeve Stock
Bore Dia.
DCB
Applicable holders
HBB 416 4
C04G-SCLC R03X1-05
HBB 516 5
C05H-SCLC R03X1-06
HBB 616 6
C06J-SCLC R04X1-07
HBB 716 7
C07K-SCLC R04X1-08
* Requires a separately-sold sleeve.
Bottom Facing
C-SCLC
Carbide
(For Torx holes)
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Steel With Vibration
Control Mechanism
B08H-SCLC R/L0602-10
10 87100
5.5
19
13
CC 0602
BFTX02505N
1. 1
TRX08
B10K-SCLC R/L0602-12
12 10 9 125
6.0
21
12
BFTX02506N
1. 5
B12M-SCLC R/L0602-14
14 12 11 150
7. 0
25
10
B12M-SCLC R/L0602-16
16 12 11 150
9.0
25
10
B16R-SCLC R/L09T3-20
20 16 15 200
11. 0
30
8
CC 09T3
BFTX0407N
3.0 TRX15
B20S-SCLC R/L09T3-25
25 20 18 250
13.0
30
7
BFTX0409N
3.4
B25T-SCLC R/L1204-32
32 25 23 300
17.0
38
6
CC 1204
BFTX0511N
5.0 TRX20
Bottom Facing
B-SCLC
Steel with
vibration
control
mechanism
(For Torx holes)
Recommended tightening torque (N·m)
Dimensions (mm)
Dimensions (mm)
This figure shows right handed tools.
95°
0°
DCON
GAMF
LF
LH
WF
H
DMIN Min.
machinable diameter
Boring
Bars
E
E14
SEC-Boring Bars
E-SCLC Type
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Applicable inserts Screws
Wrenches
R
DMIN
DCON
HLFWFLH
GAMF
Carbide
with oil hole
E08H-SCLC R0602-10 E08H-SCLC R06
10 8 7.5 100 5.5 18
13
CC 0602
BFTX02505N
1. 1
TRX08
E10K-SCLC R0602-13 E10K-SCLC R06
13 10 9.5 125 7.0 19
12
BFTX02506N
1. 5
E12M-SCLC R0602-16 E12M-SCLC R06
16 12 11.5 150 9.0 25
10
E16R-SCLC R09T3-20 E16R-SCLC R09
20 16 15.5 200 11.0 30
8
CC 09T3
BFTX0407N
3.4 TRX15
Bottom Facing
E-SCLC
Carbide
Oil hole
(For Torx holes)
Finish-Medium Cut
95°
Recommended tightening torque (N·m)
Dimensions (mm)
95°
0°
DCON
GAMF LF
LH
WF
H
DMIN Min.
machinable diameter
With oil hole
Boring
Bars
E15
E
Inserts ( Coated carbide / Cermet / Carbide)
7 Positive E Class
CCET Grades Dimensions (mm)
ACZ150
Inscribed circle
Thickness
Nose radius
FX
Cat. No.
CCET 0602003R-FX
6.35 2.38
0.03
0602003L-FX 0.03
060201R-FX 0.1
060201L-FX 0.1
060202R-FX 0.2
060202L-FX 0.2
060204R-FX 0.4
060204L-FX 0.4
CCET 09T3003R-FX
9.525 3.97
0.03
09T3003L-FX 0.03
09T301R-FX 0.1
09T301L-FX 0.1
09T302R-FX 0.2
09T302L-FX 0.2
09T304R-FX 0.4
09T304L-FX 0.4
CCET Grades Dimensions (mm)
AC530U
ACZ150
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FY
Cat. No.
CCET 03X1003R-FY
3.5 1.4
0.03
03X1003L-FY 0.03
03X101R-FY 0.1
03X101L-FY 0.1
03X102R-FY 0.2
03X102L-FY 0.2
03X104R-FY 0.4
03X104L-FY 0.4
CCET 04X1003R-FY
4.3 1.8
0.03
04X1003L-FY 0.03
04X101R-FY 0.1
04X101L-FY 0.1
04X102R-FY 0.2
04X102L-FY 0.2
04X104R-FY 0.4
04X104L-FY 0.4
CCET 0602003R-FY
6.35 2.38
0.03
0602003L-FY 0.03
060201R-FY 0.1
060201L-FY 0.1
060202R-FY 0.2
060202L-FY 0.2
060204R-FY 0.4
060204L-FY 0.4
CCET 09T3003R-FY
9.525 3.97
0.03
09T3003L-FY 0.03
09T301R-FY 0.1
09T301L-FY 0.1
09T302R-FY 0.2
09T302L-FY 0.2
09T304R-FY 0.4
09T304L-FY 0.4
7 Positive G Class
CCGT Grades Dimensions (mm)
AC1030U
AC530U
ACZ150
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FC
Cat. No.
CCGT 060201MN-FC
6.35 2.38
0.1
060202MN-FC 0.2
060204MN-FC 0.4
CCGT 09T301MN-FC
9.525 3.97
0.1
09T302MN-FC 0.2
09T304MN-FC 0.4
Nose radii with a sign "<" indicate negative tolerances.
7 Positive G Class
CCGT Grades Dimensions (mm)
AC1030U
AC530U
T1500Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FX
Cat. No.
CCGT 0602003R-FX
6.35 2.38
0.03
0602003L-FX 0.03
060201R-FX 0.1
060201L-FX 0.1
060202R-FX 0.2
060202L-FX 0.2
060204R-FX 0.4
060204L-FX 0.4
CCGT 09T3003R-FX
9.525 3.97
0.03
09T3003L-FX 0.03
09T301R-FX 0.1
09T301L-FX 0.1
09T302R-FX 0.2
09T302L-FX 0.2
09T304R-FX 0.4
09T304L-FX 0.4
09T308R-FX 0.8
09T308L-FX 0.8
CCGT Grades Dimensions (mm)
AC1030U
T1500Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FY
Cat. No.
CCGT 03X101R-FY
3.5 1.4
0.1
03X101L-FY 0.1
03X102R-FY 0.2
03X102L-FY 0.2
03X104R-FY 0.4
03X104L-FY 0.4
CCGT 04X101R-FY
4.3 1.8
0.1
04X101L-FY 0.1
04X102R-FY 0.2
04X102L-FY 0.2
04X104R-FY 0.4
04X104L-FY 0.4
SEC-Boring Bars
SCLC Type
CCGT Grades Dimensions (mm)
AC1030U
Inscribed circle
Thickness
Nose radius
FYS
Cat. No.
CCGT 03X1003R-FYS
3.5 1.4
0.03
03X1003L-FYS 0.03
03X101R-FYS 0.1
03X101L-FYS 0.1
03X102R-FYS 0.2
03X102L-FYS 0.2
03X104R-FYS 0.4
03X104L-FYS 0.4
CCGT 04X1003R-FYS
4.3 1.8
0.03
04X1003L-FYS 0.03
04X101R-FYS 0.1
04X101L-FYS 0.1
04X102R-FYS 0.2
04X102L-FYS 0.2
04X104R-FYS 0.4
04X104L-FYS 0.4
Boring
Bars
E16
E
7 Positive G Class
CCGT Grades Dimensions (mm)
AC610M
AC630M
AC510U
AC520U
AC1030U
AC530U
T1500Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
SI
Cat. No.
CCGT 09T301MN-SI
9.525 3.97
0.1
09T302MN-SI 0.2
09T304MN-SI 0.4
Nose radii with a sign "<" indicate negative tolerances.
CCGT Grades Dimensions (mm)
H1
Inscribed circle
Thickness
Nose radius
AG
Cat. No.
CCGT 060202N-AG 6.35 2.38 0.2
060204N-AG 0.4
CCGT 09T302N-AG
9.525 3.97
0.2
09T304N-AG 0.4
09T308N-AG 0.8
Inserts ( Coated carbide / Cermet / Carbide)
CCGT Grades Dimensions (mm)
AC1030U
AC530U
ACZ150
T1500Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
SC
Cat. No.
CCGT 0602003N-SC
6.35 2.38
0.03
CCGT 060201MN-SC
0.1
060202MN-SC
0.2
060204MN-SC
0.4
CCGT 09T3003N-SC
9.525 3.97
0.03
CCGT 09T301MN-SC
0.1
09T302MN-SC
0.2
Nose radii with a sign "<" indicate negative tolerances.
CCGT Grades Dimensions (mm)
H1
Inscribed circle
Thickness
Nose radius
AY
Cat. No.
CCGT 060201R-AY
6.35 2.38
0.1
060201L-AY 0.1
060202R-AY 0.2
060202L-AY 0.2
060204R-AY 0.4
060204L-AY 0.4
CCGT 09T301R-AY
9.525 3.97
0.1
09T301L-AY 0.1
09T302R-AY 0.2
09T302L-AY 0.2
09T304R-AY 0.4
09T304L-AY 0.4
CCMT Grades Dimensions (mm)
T1500A
Inscribed circle
Thickness
Nose radius
FP
Cat. No.
CCMT 060202N-FP
6.35
2.38 0.2
060208N-FP 0.8
CCMT 09T302N-FP
9.525
3.97 0.2
09T304N-FP 0.4
CCMT 120404N-FP
12.7
4.76 0.4
120408N-FP 0.8
CCMT
Grades
Dimensions (mm)
AC810P
AC820P
AC8025P
AC830P
AC610M
AC630M
AC6020M
AC6030M
AC6040M
AC520U
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
SU
Cat. No.
CCMT 060202N-SU
6.35
2.38
0.2
060204N-SU 0.4
060208N-SU 0.8
CCMT 09T302N-SU
9.525
3.97
0.2
09T304N-SU 0.4
09T308N-SU 0.8
CCMT 120404N-SU
12.7
4.76 0.4
120408N-SU 0.8
CCMT Grades Dimensions (mm)
AC820P
AC830P
AC6030M
AC6040M
T1500Z
T3000Z
T1500A
Inscribed circle
Thickness
Nose radius
LB
Cat. No.
CCMT 060202N-LB
6.35 2.38
0.2
060204N-LB 0.4
060208N-LB 0.8
CCMT 09T302N-LB
9.525 3.97
0.2
09T304N-LB 0.4
09T308N-LB 0.8
SEC-Boring Bars
SCLC Type
CCMT Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC630M
AC6030M
AC6040M
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
LU
Cat. No.
CCMT 060202N-LU 6.35 2.38 0.2
060204N-LU 0.4
CCMT 09T304N-LU 9.525 3.97 0.4
09T308N-LU 0.8
CCMT Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC630M
T1500Z
T3000Z
T1500A
Inscribed circle
Thickness
Nose radius
LUW
Cat. No.
CCMT 09T304N-LUW 9.525 3.97 0.4
09T308N-LUW 0.8
Wiper
7 Positive M Class
CCMT Grades Dimensions (mm)
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FB
Cat. No.
CCMT 060202N-FB 6.35 2.38 0.2
060204N-FB 0.4
CCMT 09T302N-FB
9.525 3.97
0.2
09T304N-FB 0.4
09T308N-FB 0.8
Boring
Bars
E17
E
Inserts (Coated carbide / Cermet / Carbide / SUMIBORON)
7 Positive M Class
CCMT Grades Dimensions (mm)
AC820P
AC8025P
A30
Inscribed circle
Thickness
Nose radius
SC
Cat. No.
CCMT 060204N-SC 6.35 2.38 0.4
CCMT 120408N-SC 12.7 4.76 0.8
CCMT Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC830P
AC630M
AC6020M
AC6030M
AC405K
AC415K
AC420K
Inscribed circle
Thickness
Nose radius
MU
Cat. No.
CCMT 09T304N-MU 9.525 3.97 0.4
09T308N-MU 0.8
CCMW
Grades Dimensions (mm)
AC405K
AC415K
AC420K
Inscribed circle
Thickness
Nose radius
Cat. No.
CCMW 060204 6.35 2.38 0.4
CCMW 09T304 9.525 3.97 0.4
09T308 0.8
SEC-Boring Bars
SCLC Type
7 Positive E Class
SUMIBORON One Use Inserts
NU-
CCEW
Grades Dimensions (mm)
BNX20
BN7000
BN700
BN7500
Inscribed circle
Thickness
Nose radius
Cat. No.
NU-CCEW 03X102LF
3.5 1.4
0.2
03X102LT 0.2
03X104LT 0.4
NU-CCEW 04X102LF
4.3 1.8
0.2
04X102LT 0.2
04X104LT 0.4
Note: The part number suffixes stand for the following: LF: Sharp edge type LT: Cutting performance focused type
7 Positive G Class
SUMIBORON Multi Corner One Use Inserts (Coated)
2NC-
CCGW
Grades Dimensions (mm)
BNC2010
BNC2020
BNC100
BNC160
BNC200
BNC300
BNC500
Inscribed circle
Thickness
Nose radius
Cat. No.
2NC-CCGW 060202
6.35 2.38
0.2
060204 0.4
060208 0.8
060202LE 0.2
060204LE 0.4
060202LT 0.2
060204LT 0.4
060202LS 0.2
060204LS 0.4
2NC-CCGW 09T302
9.525 3.97
0.2
09T304 0.4
09T308 0.8
09T304WG 0.4
09T308WG 0.8
09T304WH 0.4
09T308WH 0.8
09T302LE 0.2
09T304LE 0.4
09T308LE 0.8
09T302LT 0.2
09T304LT 0.4
09T308LT 0.8
09T302LS 0.2
09T304LS 0.4
09T308LS 0.8
09T304HS 0.4
09T308HS 0.8
Note: The part number suffixes stand for the following: WG/WH: Wiper insert LE: Low resistance type
LT/LS: Cutting performance focused type HS: Strengthened cutting edge type
SUMIBORON Break Master (Coated)
2NC-
CCGT
Grades Dimensions (mm)
BNC2010
BNC2020
BNC160
BNC200
Inscribed circle
Thickness
Nose radius
FV/LV
Cat. No.
2NC-CCGT 060204N-FV 6.35 2.38 0.4
2NC-CCGT 09T304N-FV
9.525 3.97
0.4
09T308N-FV 0.8
09T304N-LV 0.4
09T308N-LV 0.8
Boring
Bars
E18
E
mark: To be replaced by new item (Please confirm stock availability)
Inserts ( SUMIBORON / SUMIDIA)
7 Positive M Class
SUMIDIA NF Inserts
NF
CCMT
Grades Dimensions (mm)
DA1000
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
NF-CCMT 060201
6.35 2.38
0.1
060202 0.2
060204 0.4
NF-CCMT 09T301
9.525 3.97
0.1
09T302 0.2
09T304 0.4
09T308 0.8
SUMIDIA Break Master
NF
CCMT
Grades Dimensions (mm)
DA1000
Inscribed circle
Thickness
Nose radius
LD/GD
Cat. No.
NF-CCMT 060202N-LD
6.35 2.38
0.2
060204N-LD 0.4
060202N-GD 0.2
060204N-GD 0.4
NF-CCMT 09T302N-LD
9.525 3.97
0.2
09T304N-LD 0.4
09T308N-LD 0.8
09T302N-GD 0.2
09T304N-GD 0.4
09T308N-GD 0.8
Note:
The part number suffixes stand for the following: LD: For finishing GD: For medium finishing
SUMIDIA
CCMT Grades Dimensions (mm)
DA150
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
CCMT 060201
6.35 2.38
0.1
060202 0.2
060204 0.4
CCMT 09T301
9.525 3.97
0.1
09T302 0.2
09T304 0.4
7 Positive G Class
SUMIBORON Multi Corner One Use Inserts (Non-Coated)
2NU-
CCGW
Grades Dimensions (mm)
BN2000
BN7000
BN7500
Inscribed circle
Thickness
Nose radius
Cat. No.
2NU-CCGW 060204 6.35 2.38 0.4
2NU-CCGW 09T304
9.525 3.97
0.4
09T308 0.8
09T304WG 0.4
09T308WG 0.8
09T304WH 0.4
09T308WH 0.8
Note: The part number suffixes stand for the following: WG/WH: Wiper insert
SUMIBORON One Use Inserts (Non-Coated)
NU-
CCGW
Grades Dimensions (mm)
BN1000
BN2000
BN7000
BN700
Inscribed circle
Thickness
Nose radius
Cat. No.
NU-CCGW 060202
6.35 2.38
0.2
060204 0.4
060208 0.8
060202LT 0.2
060204LT 0.4
060208LT 0.8
060202HS 0.2
060204HS 0.4
NU-CCGW 09T302
9.525 3.97
0.2
09T304 0.4
09T308 0.8
09T302LT 0.2
09T304LT 0.4
09T308LT 0.8
09T302HS 0.2
09T304HS 0.4
09T308HS 0.8
Note: The part number suffixes stand for the following: LT: Cutting performance focused type
HS: Strengthened cutting edge type
SUMIBORON Break Master (Non-Coated)
2NU-
CCGT
Grades Dimensions (mm)
BN2000
Inscribed circle
Thickness
Nose radius
FV/LV
Cat. No.
2NU-CCGT 060204N-FV 6.35 2.38 0.4
2NU-CCGT 09T304N-FV
9.525 3.97
0.4
09T308N-FV 0.8
09T304N-LV 0.4
09T308N-LV 0.8
SEC-Boring Bars
SCLC Type
SUMIDIA Binderless
CCMW
Grades Dimensions (mm)
NPD10
Inscribed circle
Thickness
Nose radius
RH
Cat. No.
CCMW 03X102RH 3.50 1.40 0.2
03X104RH 0.4
CCMW 04X102RH 4.30 1.80 0.2
04X104RH 0.4
CCMW 060202RH 6.35 2.38 0.2
060204RH 0.4
CCMW 09T302RH
9.525 3.97
0.2
09T304RH 0.4
09T308RH 0.8
Boring
Bars
E19
E
GAMF
f
95°
LF
H
DCON
5°
LH
DMIN Min.
machinable diameter
With oil hole
SEC-Boring Bars
S-SCLP Type / A-SCLP Type
Finish-Medium Cut
Parts
Holders
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Steel
S10K-SCLP R/L0802-12 BBPC-010 R/L 12 10 9 125
6.0 12.0
5
CP 0802
BFTX0305A
2.0 TRX10
S12M-SCLP R/L0802-14 BBPC-012 R/L14 14 12 11 150
7.0 10.6
5
S12M-SCLP R/L0802-16 BBPC-012 R/L 16 12 11 150
8.0 15.0
3
S12M-SCLP R/L0903-16 16 12 11 150
8.0 23.0
6
CP 0903
BFTX0407A
3.4 TRX15
S16R-SCLP R/L0903-18 BBPC-316 R/L18 18 16 15 200
9.0 18.0
4
S16R-SCLP R/L0903-20 BBPC-316 R/L 20 16 15 200
10.0 18.0
3
S20S-SCLP R/L0903-22 BBPC-320 R/L22 22 20 18 250
11.0 18.0
2
S20S-SCLP R/L0903-25 BBPC-320 R/L 25 20 18 250
12.5 18.0
0
S25T-SCLP R/L0903-27 27 25 22 300
13.5 18.0
2
S25T-SCLP R/L0903-28 BBPC-325 R/L 28 25 22 300
14.0 35.0
2
S25T-SCLP R/L1204-28 BBPC-425 R/L 28 25 22 300
14.0 17.4
2
CP 1204
BFTX0509A
5.0 TRX20
Bottom Facing
S-SCLP
Steel
(For Torx holes)
95°
Recommended tightning torque (N m) mark: To be replaced by new item (Please confirm stock availability)
Parts
Parts
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Steel with oil hole
A10K-SCLP R/L0802-12 12 10 9 125
6.0 12.0
5
CP 0802
BFTX0305N
2.0 TRX10
A12M-SCLP R/L0802-14 14 12 11 150
7.0 10.6
5
BFTX0306N
2.0
A12M-SCLP R/L0903-16 16 12 11 150
8.0 23.0
6
CP 0903
BFTX0407N
3.4 TRX15
A16R-SCLP R/L0903-18 18 16 15 200
9.0 18.0
4
A20S-SCLP R/L0903-22 22 20 18 250
11.0 18.0
2
A25T-SCLP R/L0903-27 27 25 22 300
13.5 18.0
2
Bottom Facing
A-SCLP
Steel
(For Torx holes)
This figure shows right handed tools.
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
95°
5°
DCON
GAMF
LF
LH
WF
H
DMIN Min.
machinable diameter
Boring
Bars
E20
E
SEC-Boring Bars
B-SCLP Type / D-SCLP Type / C-SCLP Type
Finish-Medium Cut
95°
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Conventional Cat.
No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Carbide
C10K-SCLP R/L0802-12
WBPC-010 R/L S
12 10 9 125 6 19 5
CP 0802
BFTX0305A
2.0 TRX10
C12M-SCLP R/L0802-14
WBPC-012 R/L S14
14 12 11 150 7 25 5
C12M-SCLP R/L0802-16
WBPC-012 R/L S
16 12 11 150 8 25 3
C16R-SCLP R/L0903-18
WBPC-316 R/L S18
18 16 15 200 9 30 4
CP 0903
BFTX0407A
3.4 TRX15
C16R-SCLP R/L0903-20
WBPC-316 R/L S
20 16 15 200 10 30 3
Bottom Facing
C-SCLP
Carbide
(For Torx holes)
Bottom Facing
B-SCLP
Bottom Facing
D-SCLP
Steel with
vibration
control
mechanism
Oil hole
Steel with
vibration
control
mechanism
95°
5°
Fig 1
DCON
GAMF LF
LH
WF
H
DMIN Min.
machinable diameter
95°
5°
Fig 2
DCON
GAMF LF
LH
WF
H
DMIN Min.
machinable diameter
With oil hole
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Conventional Cat.
No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Fig Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Steel with vibration
control mechanism
B12M-SCLP R/L0802-14 XBPC-012 R/L14
14 12 11 150 7
10.6
51
CP 0802
BFTX0305A
2.0 TRX10
B16R-SCLP R/L0903-18 XBPC-316 R/L18
18 16 15 200 9
18.0
41
CP 0903
BFTX0407A
3.4 TRX15
B20S-SCLP R/L0903-22 XBPC-320 R/L22
22 20 18 250 11
18.0
2
D12M-SCLP R/L0802-14 XBPC-012 R/L H14
14 12 11 150 7
10.6
52
CP 0802
BFTX0305A
2.0 TRX10
D16R-SCLP R/L0903-18 XBPC-316 R/L H18
18 16 15 200 9
18.0
42
CP 0903
BFTX0407A
3.4 TRX15
D20S-SCLP R/L0903-22 XBPC-320 R/L H22
22 20 18 250 11
18.0
2
(For Torx holes)
Recommended tightening torque (N·m)
This figure shows right handed tools.
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
95°
5°
DCON
GAMF LF
LH
WF
H
DMIN Min.
machinable diameter
Boring
Bars
E
E21
SEC-Boring Bars
SCLP Type
Inserts ( Coated carbide / Cermet / Carbide)
11 Positive G Class
CPGT Grades Dimensions (mm)
AC510U
T1500Z
T3000Z
T1000A
T1500A
G10E
Inscribed circle
Thickness
Nose radius
SD
Cat. No.
CPGT 080202N-SD
7.94
2.38
0.2
080204N-SD 0.4
080208N-SD 0.8
CPGT 090302N-SD
9.525
3.18
0.2
090304N-SD 0.4
090308N-SD 0.8
CPGT 120402N-SD
12.70
4.76
0.2
120404N-SD 0.4
120408N-SD 0.8
CPMT
Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC630M
AC6030M
AC6040M
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
LU
Cat. No.
CPMT 080204N-LU 7.94 2.38 0.4
CPMT 090304N-LU 9.525 3.18 0.4
090308N-LU 0.8
11 Positive M Class
CPMT
Grades Dimensions (mm)
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FB
Cat. No.
CPMT 080204N-FB 7.94 2.38 0.4
CPMT 090304N-FB 9.525 3.18 0.4
090308N-FB 0.8
CPMT Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC630M
T1500Z
T3000Z
T1500A
Inscribed circle
Thickness
Nose radius
LUW
Cat. No.
CPMT 090304N-LUW 9.525 3.18 0.4
090308N-LUW 0.8
11 Positive M Class
CPMT Grades Dimensions (mm)
AC810P
AC820P
AC630M
AC6030M
AC405K
AC415K
AC420K
Inscribed circle
Thickness
Nose radius
MU
Cat. No.
CPMT 080204N-MU 7.94 2.38 0.4
080208N-MU 0.8
CPMT 090304N-MU 9.525 3.18 0.4
090308N-MU 0.8
CPMW
Grades Dimensions (mm)
AC405K
AC415K
AC420K
Inscribed circle
Thickness
Nose radius
Cat. No.
CPMW 080204 7.94 2.38 0.4
080208 0.8
CPMW 090304 9.525 3.18 0.4
090308 0.8
Wiper
CPMT
Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC830P
AC610M
AC630M
AC6020M
AC6030M
AC6040M
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
SU
Cat. No.
CPMT 080204N-SU 7.94 2.38 0.4
080208N-SU 0.8
CPMT 090304N-SU 9.525 3.18 0.4
090308N-SU 0.8
CPMT Grades Dimensions (mm)
AC820P
AC8025P
AC830P
AC6020M
AC6030M
AC6040M
T1500Z
T3000Z
T1500A
Inscribed circle
Thickness
Nose radius
LB
Cat. No.
CPMT 080204N-LB 7.94 2.38 0.4
CPMT 090304N-LB 9.525 3.18 0.4
090308N-LB 0.8
Boring
Bars
E22
E
SEC-Boring Bars
SCLP Type
11 Positive M Class
Inserts ( SUMIBORON / SUMIDIA)
11 Positive G Class
SUMIBORON Multi Corner One Use Inserts (Coated)
2NC-
CPGW
Grades Dimensions (mm)
BNC2010
BNC2020
Inscribed circle
Thickness
Nose radius
Cat. No.
2NC-CPGW 080202
7.94 2.38
0.2
080204 0.4
090302 0.2
090304 0.4
SUMIBORON One Use Inserts
NU-
CPGW
Grades Dimensions (mm)
BN1000
BN2000
Inscribed circle
Thickness
Nose radius
Cat. No.
NU-CPGW 080202
7.94 2.38
0.2
080204 0.4
080208 0.8
080204LT 0.4
080202HS 0.2
080204HS 0.4
080208HS 0.8
NU-CPGW 090302
9.525 3.18
0.2
090304 0.4
090308 0.8
090302LT 0.2
090304LT 0.4
090308LT 0.8
090302HS 0.2
090304HS 0.4
090308HS 0.8
Note: The part number suffixes stand for the following:
LT: Cutting performance focused type HS: Strengthened cutting edge type
SUMIDIA NF Inserts
NF-
CPMT
Grades Dimensions (mm)
DA1000
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
NF-CPMT 090302
9.525 3.18
0.2
090304 0.4
090308 0.8
SUMIDIA
CPMT Grades Dimensions (mm)
DA1000
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
CPMT 080202
7.94 2.38
0.2
080204 0.4
080208 0.8
CPMT 090302
9.525 3.18
0.2
090304 0.4
090308 0.8
mark: To be replaced by new item (Please confirm stock availability)
Boring
Bars
E23
E
General Boring
Parts
Holders The applicable insert direction depends on the process details.
(See the notes marked with an asterisk (*) at the bottom of this page.)
Holder
Material
Cat. No.
Conventional
Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Offset
set
Fig
Applicable inserts Clamp
sets Shim Screw for
shim
Wrenches
for upper
surface
Wrenches
for lower
surface
RL
DMIN
DCON
HLF
WF
LH E1 Cat. No.
Page
Steel
S25R-DCLN R/L0903-32
32 25 23
200
17.0
18 4.5 1
CN 0903
B20
SCP-1 5.0 LH040 LH025
S25T-DCLN R/L0903-32
S25T-DCLN R/L09
32 25 23
300
17.0
18 4.5
S32S-DCLN R/L1204-40
40 32 30
250
22.0
26 7.0 2
CN 1204
From
B22
SCP-2 5.0
CNS1204B
BFTX0409N
LH040 LH025
S40T-DCLN R/L1204-50
50 40 37
300
27.0
26 8.5
S50U-DCLN R/L1204-63
63 50 47
350
31.5
36 8.0 3
Inserts
CNMG090308N-GU
(Representative
example)
S-DCLN
Bottom Facing
Steel
– 6°
–10°
95°
DCON
E1
LH
LF
WF
H
DMIN Min.
machinable diameter
SEC-Boring Bars
S-DCLN Type / D-DCLN Type
95°
D-DCLN
Bottom Facing Oil hole
Steel with
vibration
control
mechanism
95°
– 6°
DCON
GAMF
LF
LH
WF
H
DMIN Min.
machinable diameter
Parts
Holders
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height Length
Cutting edge
distance Head
Rake
angle Applicable inserts Clamp
set Shims Screws
for shim
Wrenches
for upper
surface
Wrenches
for lower
surface
RL
DMIN
DCON
HLF
WF
LH
GAMF
Cat. No.
Page
Vibration
control
mechanism
steel with
oil hole
D
25T-DCLN R/L1204-32
32 25 23 300 17 26
12
CN 1204
From
B22 SCP-2 5.0
CNS1203B
BFTX0307N
LH040 LH025
D32T-DCLN R/L1204-40
40 32 30 300 22 26
10
CNS1204B
BFTX0409N
D40U-DCLN R/L1204-50
50 40 37 350 27 26
10
CNMG120408N-GE
(Representative
example)
Inserts
Parts for clamp set
E81
Parts for clamp set
E81
-6°
2
Fig2
-6°
Fig3
L2
Fig1
This figure shows right handed tools.
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
mark: Standard stocked item (expanded product)
Note: About Applicable Inserts for DCLN Type
For internal machining: Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts; left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
For facing: Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts; left-handed (L) holders are applicable for left-handed (L) and neutral (N) inserts.
Recommended tightening torque (N·m)
Boring
Bars
E24
E
95°
-6°
DCON
GAMF
LF
WF
E1
H
DMIN Min.
machinable diameter
– 6°
95°
DCON
GAMF LF
E1
LH
WF
H
DMIN Min.
machinable diameter
SEC-Boring Bars
S-PCLN Type / B-PCLN Type
95°
B-PCLN
Bottom Facing
–10°
95°
DCON
LF
LH
E1
WF
H
DMIN Min.
machinable diameter
Parts
Holders
The applicable insert direction depends on the process details.
(See the notes marked with an asterisk (*) at the bottom of this page.)
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Offset
Applicable inserts Lever
pin Bolts Shim Shim
retainer Wrench
RL
DMIN
DCON
HLFWFLHE1 Cat. No. Page
Steel with
vibration
control
mechanism
B32U -PCLN R/L1204-40
40 32 30 350 20 29 5.0
CN 1204
B22–
LCL4
LCS4CA
LSC42B LSP4 LH030
B40W-PCLN R/L1204-50
50 40 37 450 25 29 6.5 LCS4
Steel with
vibration
control
mechanism
CNMG120408N-GE
(Representative example)
Inserts
Parts
Holders The applicable insert direction depends on the process details. (See the notes
marked with an asterisk (*) at the bottom of this page.)
Holder
Material
Cat. No.
Conventional
Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Offset
Rake
angle Fig
Applicable inserts
Lever
pins Bolts Shims
Shim
retainers
Wrenches
RL
DMIN
DCON
HLFWFLHE1
GAMF
Cat. No. Page
Steel
S25R-PCLN R/L0903-32
32 25 23 200
17.0
30
4.5
15
1
CN 0903
B20
LCL3 LCS3 LSC32 LSP3 LH025
S32S-PCLN R/L1204-40
40 32 30 250
22.0
29
7. 0
10
1
CN 1204
From
B22
LCL4 LCS4
LSC42B
LSP4 LH030
S32S-PCLN R/L1204-44
S32S-PCLN R/L12
44 32 30 250
22.0
29
7. 0
10
S40T-PCLN R/L1204-50
50 40 37 300
25.0
29
6.5
10
S40T-PCLN R/L1204-54
S40T-PCLN R/L12
54 40 37 300
27.0
29
8.5
10
LSC42
S50U-PCLN R/L1204-63
63 50 47 350
31.5 8.0
10
2
LSC42B
S50U-PCLN R/L1906-70
S50U-PCLN R/L19
70 50 47 350
35.0
39
11. 5
10
1
CN 1906
From
B28
LCL6 LCS6 LSC63 LSP6 LH040
S-PCLN
Bottom Facing
Steel
Fig 1 Fig 2
This figure shows right handed tools.
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
mark: Standard stocked item (expanded product)
Note: About Applicable Inserts for PCLN Type
For internal machining: Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts; left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
For facing: Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts; left-handed (L) holders are applicable for left-handed (L) and neutral (N) inserts.
Boring
Bars
E25
E
-6°
-12°
-6°
95°
DCON
GAMF
LF
WF
H
DMIN Min.
machinable diameter
-6°
95°
DCON
GAMF
LF
LH
WF
H
DMIN Min.
machinable diameter
Parts
Holders The applicable insert direction depends on the process details.
(See the notes marked with an asterisk (*) at the bottom of this page.)
Holder
Material
Cat. No. Conventional
Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Offset
Rake
angle Applicable inserts Shims Eccentric
shafts Wrenches
RL
DMIN
DCON
HLFWFLHE1
GAMF
Cat. No. Page
Steel
S20Q-ECLN R/L0903-26
BCLN320 R/L
26 20 18 180 13 20
4.0
12
CN 0903
B20
CPU304C
LH030
S25R-ECLN R/L0903-34
BCLN325 R/L
34 25 23 200 17 20
5.5
12
SCW323
CPB32C
LH025
S25R-ECLN R/L1204-34
BCLN425 R/L
34 25 23 200 17 20
5.5
12
CN 1204
From
B22 SCW423
CPB42
LH030
S32S-ECLN R/L1204-44
BCLN432 R/L
44 32 30 250 22 25
7. 0
10
CPB43S
S40T-ECLN R/L1204-54
BCLN440 R/L
54 40 37 300 27 25
8.5
10
CPB43
S50U-ECLN R/L1906-70
BCLN650 R/L
70 50 47 350 35 32
11. 5
10
CN 1906
From
B28 SCW635
CPB64
LH040
Inserts
CNMG090308N-UX
CNMG120408N-GE
CNMG190612N-UX
(Representative example)
GE Type
UX Type
S-ECLN
Bottom Facing
Steel 95°
– 6°
DCON
GAMF
LF
LH
E1
WF
H
DMIN Min.
machinable diameter
95°
SEC-Boring Bars
S-ECLN Type / S-DWLN Type
95°
Recommended tightning torque(N m) mark: Standard stocked item (expanded product)
S-DWLN
Bottom Facing
Steel
Fig 1 Fig 2
Parts
Holders
The applicable insert direction depends on the process details.
(See the notes marked with an asterisk (*) at the bottom of this page.)
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Fig Applicable inserts Clamp
sets Shims Screws
for shims
Wrenches
for upper
surface
Wrenches
for lower
surface
RL
DMIN
DCON
HLFWFLH
GAMF
Cat. No. Page
Steel
S32S-DWLN R/L0604-40
40 32 30 250 22.0 29
10
1
WN 0604
From
B69 SCP-4 5.0
WNS0603B
BFTX0307N
LH040 LH025
S25R-DWLN R/L0804-32
32 25 23 200 17.0 26
12
1
WN 0804
From
B71 SCP-2 5.0
WNS0803B
BFTX0307N
LH040 LH025
S32S-DWLN R/L0804-40
40 32 30 250 22.0 26
12
WNS0804B
BFTX0409N
S40T-DWLN R/L0804-50
50 40 37 300 27.0 26
12
S50U-DWLN R/L0804-63
63 50 47 350 31.5
12
2
Parts for clamp set
E81
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
Note: About Applicable Inserts for ECLN Type and DWLN Type
For internal machining: Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts; left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
For facing: Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts; left-handed (L) holders are applicable for left-handed (L) and neutral (N) inserts.
Boring
Bars
E26
E
SEC-Boring Bars
D-DWLN Type / S-PWLN Type
95°
General Boring
Parts
Holders
Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts;
left-handed (L) holders are applicable for left-handed (L) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Applicable inserts Lever
pins Bolts Shims
Shim
retainers
Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Cat. No. Page
Steel
S32S-PWLN R/L0604-40 40 32 30 250 22 29
10
WN 0604
From
B69 LCL3 LCS3
LSW317
LSP3 LH025
S32S-PWLN R/L0804-40 40 32 30 250 22 29
10
WN 0804
From
B71 LCL4 LCS4
LSW42B
LSP4 LH030
S40T-PWLN R/L0804-50 50 40 37 300 27 29
10
S-PWLN
Bottom Facing
Steel
95°
-6°
DCON
GAMF
LF
LH
WF
H
DMIN Min.
machinable diameter
WNMG080408N-GE
(Representative example)
Inserts
Recommended tightning torque(N m)
mark: Standard stocked item (expanded product)
D-DWLN
Bottom Facing Oil hole
Steel with
vibration
control
mechanism
95°
– 6°
DCON
GAMF
LF
LH
WF
H
DMIN Min.
machinable diameter
Parts
Holders The applicable insert direction depends on the process details.
(See the notes marked with an asterisk (*) at the bottom of this page.)
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Applicable inserts Clamp
set Shims Screws
for shim
Wrench
for upper
surface
Wrench
for lower
surface
RL
DMIN
DCON
HLFWFLH
GAMF
Cat. No. Page
Vibration
control
mechanism
Steel with
oil hole
D25T-DWLN R/L0804-32
32 25 23 300 17 26
12
WN 0804
From
B71 SCP-2 5.0
WNS0803B
BFTX0307N
LH040 LH025
D32T-DWLN R/L0804-40
40 32 30 300 22 26
10
WNS0804B
BFTX0409N
D40U-DWLN R/L0804-50
50 40 37 350 27 26
10
WNMG080408N-GE
(Representative example)
Inserts
Parts for clamp set
E81
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
Note: About Applicable Inserts for DWLN Type and PWLN Type
For internal machining: Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts; left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
For facing: Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts; left-handed (L) holders are applicable for left-handed (L) and neutral (N) inserts.
Boring
Bars
E27
E
0°
LH
0°
93°
E1
H
DCON
LF
GAMF
WF
Fig1
Fig2
DMIN Min.
machinable diameter
With oil hole
Profiling
S-SDUC
Steel
Fig 1 Fig 2
0°
93°
DCON
GAMF
LF
E1
WF
H
DMIN Min.
machinable diameter
0°
93°
DCON
GAMF
LF
LH
WF
H
E1
DMIN Min.
machinable diameter
SEC-Boring Bars
S-SDUC Type / A-SDUC Type
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Conventional
Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset
Rake
angle
Head
Fig
Applicable inserts
Screws
Wrenches
RL
DMIN
DCON
HLFWFE1
GAMF
LH
Steel
S10M-SDUC R/L0702-13
S10M-SDUC R/L07
13 10 9 150
7. 0
2.5 8
1
DC 0702
BFTX02506N
1. 5 TRX08
S12M-SDUC R/L0702-16
S12M-SDUC R/L07
16 12 11 150
9.0
3.5 8
S16Q-SDUC R/L0702-20
20 16 15 180
11. 0
4.0 6
S16N-SDUC R/L0702-20
S16N-SDUC R/L07
20 16 15 160
11. 0
4.0 6
S16Q-SDUC R/L11T3-23
23 16 15 180
12.5
5.5 615 2
DC 11T3
BFTX0409N
3.4 TRX15
S20R-SDUC R/L11T3-25
25 20 18 200
13.0
4.5 6
1
S20N-SDUC R/L11T3-25
S20N-SDUC R/L11
25 20 18 160
13.0
4.5 6
S25S-SDUC R/L11T3-32
32 25 22 250
17.0
7. 0 6
S25Q-SDUC R/L11T3-32
S25Q-SDUC R/L11
32 25 22 180
17.0
7. 0 6
Internal Profiling
93˚
(For Torx holes)
Recommended tightning torque(N m) mark: Standard stocked item (expanded product)
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset
Rake
angle
Head
Fig Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFE1
GAMF
LH
Steel with oil hole
A10M-SDUC R/L0702-13 13 10 9 150
7. 0
2.5 8
1DC 0702
BFTX02506N
1. 5 TRX08
A12M-SDUC R/L0702-16 16 12 11 150
9.0
3.5 8
A16Q-SDUC R/L0702-20 20 16 15 180
11. 0
4.0 6
A16Q-SDUC R/L11T3-23 23 16 15 180
12.5
5.5 615 2
DC 11T3
BFTX0409N
3.4 TRX15
A20R-SDUC R/L11T3-25 25 20 18 200
13.0
4.5 61
A25S-SDUC R/L11T3-32 32 25 22 250
17.0
7. 0 6
A-SDUC
Profiling
Steel
(For Torx holes)
This figure shows right handed tools.
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
Boring
Bars
E
E28
SEC-Boring Bars
B-SDUC Type / C-SDUC Type
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset
Rake
angle Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFE1
GAMF
Steel with vibration
control mechanism
B10M-SDUC R/L0702-13 13 10 9 150 7 2.5 8
DC 0702
BFTX02506N
1. 5 TRX08
B12M-SDUC R/L0702-16 16 12 11 150 9 3.5 8
B16R-SDUC R/L0702-20 20 16 15 200 11 4.0 6
B20S-SDUC R/L11T3-25 25 20 18 250 13 4.5 6DC 11T3
BFTX0409N
3.4 TRX15
B25S-SDUC R/L11T3-32 32 25 22 250 17 7.0 6
Profiling
B-SDUC
Steel with
vibration
control
mechanism
0°
93°
DCON
GAMF
LF
WF
E1
H
DMIN Min.
machinable diameter
(For Torx holes)
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset
Rake
angle Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFE1
GAMF
Carbide
C10M-SDUC R/L0702-13 13 10 9 150 7 2.5 8
DC 0702
BFTX02506N
1. 5 TRX08
C12M-SDUC R/L0702-16 16 12 11 150 9 3.5 8
C16R-SDUC R/L0702-20 20 16 15 200 11 4.0 6
C20S-SDUC R/L11T3-25 25 20 18 250 13 4.5 6DC 11T3
BFTX0409N
3.4 TRX15
Profiling
C-SDUC
Carbide
0°
93°
DCON
GAMF
LF
H
WF
E1
DMIN Min.
machinable diameter
(For Torx holes)
Recommended tightening torque (N·m)
This figure shows right handed tools.
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
Boring
Bars
E29
E
107.5°
0°
DCON
GAMF
LF
LH
WF
E1
H
DMIN Min.
machinable diameter
SEC-Boring Bars
S-SDQC Type / A-SDQC Type
Internal Profiling
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Conventional Cat.
No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset
Rake
angle
Head
Fig
Applicable inserts
Screws
Wrenches
RL
DMIN
DCON
HLFWFE1
GAMF
LH
Steel
S10M-SDQC R/L0702-13
S10M-SDQC R/L07
13 10 9 150
7. 0
2.5 8
1
DC 0702
BFTX02506N
1. 5 TRX08
S12M-SDQC R/L0702-16
S12M-SDQC R/L07
16 12 11 150
9.0
3.5 8
S16Q-SDQC R/L0702-20
20 16 15 180
11. 0
4.0 6
S16N-SDQC R/L0702-20
S16N-SDQC R/L07
20 16 15 160
11. 0
4.0 6
S16Q-SDQC R/L11T3-23
23 16 15 180
12.5
5.5 615 2
DC 11T3
BFTX0409N
3.4 TRX15
S20R-SDQC R/L11T3-25
25 20 18 200
13.0
4.5 6
1
S20N-SDQC R/L11T3-25
S20N-SDQC R/L11
25 20 18 160
13.0
4.5 6
S25S-SDQC R/L11T3-32
32 25 22 250
17.0
7. 0 6
S25Q-SDQC R/L11T3-32
S25Q-SDQC R/L11
32 25 22 180
17.0
7. 0 6
Profiling
S-SDQC
Steel
Fig 1 Fig 2
0°
107.5°
DCON
GAMF
LF
WF
E1
H
DMIN Min.
machinable diameter
107.5°
(For Torx holes)
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset
Rake
angle
Head
Fig Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFE1
GAMF
LH
Steel with oil hole
A10M-SDQC R/L0702-13 13 10 9 150
7. 0
2.5 8
1DC 0702
BFTX02506N
1. 5 TRX08
A12M-SDQC R/L0702-16 16 12 11 150
9.0
3.5 8
A16Q-SDQC R/L0702-20 20 16 15 180
11. 0
4.0 6
A16Q-SDQC R/L11T3-23 23 16 15 180
12.5
5.5 615 2
DC 11T3
BFTX0409N
3.4 TRX15
A20R-SDQC R/L11T3-25 25 20 18 200
13.0
4.5 61
A25S-SDQC R/L11T3-32 32 25 22 250
17.0
7. 0 6
Profiling
A-SDQC
Steel
Oil hole
(For Torx holes)
Recommended tightning torque(N m) mark: Standard stocked item (expanded product)
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
WF
E1
DCON
LF
0°
H
GAMF
107.5°
Fig2
Fig1
LH
0°
DMIN Min.
machinable diameter
With oil hole
Boring
Bars
E30
E
SEC-Boring Bars
B-SDQC Type / S-SDZC Type
Recommended tightning torque(N m)
mark: Standard stocked item (expanded product)
Internal Profiling
Parts
Holders
Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts.
Left handed (L) holders are applicable for left handed (L) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset
Rake
angle Fig Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFE1
GAMF
Steel
S10M-SDZC R/L0702-13 13 10 9 150
7. 5
3.0 81DC 0702 BFTX02506N 1. 5 TRX08
S12M-SDZC R/L0702-16 16 12 11 150
9.0
3.5 8
S16Q-SDZC R/L0702-20 20 16 15 180
11. 0
4.0 62
S16Q-SDZC R/L11T3-23 23 16 15 180
13.0
6.0 63
DC 11T3 BFTX0409N 3.4 TRX15
S20R-SDZC R/L11T3-25 25 20 18 200
14.5
6.0 64
S25S-SDZC R/L11T3-32 32 25 22 250
17.0
7. 0 6
Profiling
S-SDZC
Steel
Fig 1 Fig 2
10
93°
0°
DCON
GAMF
LF
WF
E1
H
DMIN Min.
machinable diameter
10
93°
0°
DCON
GAMF
LF
WF
E1
H
DMIN Min.
machinable diameter
Fig 3 Fig 4
15
0°
DCON
GAMF
LF
WF
E1
H
DMIN Min.
machinable diameter
93°
0°
93°
15
DCON
GAMF
LF
WF
E1
H
DMIN Min.
machinable diameter
(For Torx holes)
93°
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset
Rake
angle Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFE1
GAMF
Steel with vibration
control mechanism
B10M-SDQC R/L0702-13 13 10 9 150 7 2.5 8
DC 0702
BFTX02506N
1. 5 TRX08
B12M-SDQC R/L0702-16 16 12 11 150 9 3.5 8
B16R-SDQC R/L0702-20 20 16 15 200 11 4.0 6
B20S-SDQC R/L11T3-25 25 20 18 250 13 4.5 6DC 11T3
BFTX0409N
3.4 TRX15
B25S-SDQC R/L11T3-32 32 25 22 250 17 7.0 6
Profiling
B-SDQC
Steel with
vibration
control
mechanism
0°
107.5°
DCON
GAMF
LF
WF
E1
H
DMIN Min.
machinable diameter
(For Torx holes)
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
Boring
Bars
E31
E
Inserts ( Coated carbide / Cermet / Carbide)
7 Positive G Class
DCGT Grades Dimensions (mm)
AC520U
AC1030U
AC530U
ACZ150
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FC
Cat. No.
DCGT 070201MN-FC
6.35 2.38
0.1
070202MN-FC 0.2
070204MN-FC 0.4
DCGT 11T301MN-FC
9.525 3.97
0.1
11T302MN-FC 0.2
11T304MN-FC 0.4
Nose radii with a sign "<" indicate negative tolerances.
7 Positive G Class
DCGT Grades Dimensions (mm)
AC1030U
AC520U
AC530U
T1500Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FX
Cat. No.
DCGT 0702003R-FX
6.35 2.38
0.03
0702003L-FX 0.03
070201R-FX 0.1
070201L-FX 0.1
070202R-FX 0.2
070202L-FX 0.2
070204R-FX 0.4
070204L-FX 0.4
DCGT 11T3003R-FX
9.525 3.97
0.03
11T3003L-FX 0.03
11T301R-FX 0.1
11T301L-FX 0.1
11T302R-FX 0.2
11T302L-FX 0.2
11T304R-FX 0.4
11T304L-FX 0.4
SEC-Boring Bars
SDUC Type / SDQC Type
DCGT Grades Dimensions (mm)
AC1030U
AC520U
AC530U
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FY
Cat. No.
DCGT 0702003R-FY
6.35 2.38
0.03
0702003L-FY 0.03
070201R-FY 0.1
070201L-FY 0.1
070202R-FY 0.2
070202L-FY 0.2
070204R-FY 0.4
070204L-FY 0.4
DCGT 11T3003R-FY
9.525 3.97
0.03
11T3003L-FY 0.03
11T301R-FY 0.1
11T301L-FY 0.1
11T302R-FY 0.2
11T302L-FY 0.2
11T304R-FY 0.4
11T304L-FY 0.4
DCGT Grades Dimensions (mm)
AC1030U
Inscribed circle
Thickness
Nose radius
FYS
Cat. No.
DCGT 0702003R-FYS
6.35 2.38
0.03
0702003L-FYS 0.03
070201R-FYS 0.1
070201L-FYS 0.1
070202R-FYS 0.2
070202L-FYS 0.2
070204R-FYS 0.4
070204L-FYS 0.4
DCGT 11T3003R-FYS
9.525 3.97
0.03
11T3003L-FYS 0.03
11T301R-FYS 0.1
11T301L-FYS 0.1
11T302R-FYS 0.2
11T302L-FYS 0.2
11T304R-FYS 0.4
11T304L-FYS 0.4
7 Positive E Class
DCET Grades Dimensions (mm)
ACZ150
Inscribed circle
Thickness
Nose radius
FX
Cat. No.
DCET 0702003R-FX
6.35 2.38
0.03
0702003L-FX 0.03
0702008R-FX 0.08
0702008L-FX 0.08
070201R-FX 0.1
070201L-FX 0.1
0702018R-FX 0.18
0702018L-FX 0.18
070204R-FX 0.4
070204L-FX 0.4
DCET 11T3003R-FX
9.525 3.97
0.03
11T3003L-FX 0.03
11T3008R-FX 0.08
11T3008L-FX 0.08
11T301R-FX 0.1
11T301L-FX 0.1
11T3018R-FX 0.18
11T3018L-FX 0.18
11T304R-FX 0.4
11T304L-FX 0.4
DCET Grades Dimensions (mm)
ACZ150
Inscribed circle
Thickness
Nose radius
FY
Cat. No.
DCET 0702003R-FY
6.35 2.38
0.03
0702003L-FY 0.03
0702008R-FY 0.08
0702008L-FY 0.08
070201R-FY 0.1
070201L-FY 0.1
0702018R-FY 0.18
0702018L-FY 0.18
070204R-FY 0.4
070204L-FY 0.4
DCET 11T3003R-FY
9.525 3.97
0.03
11T3003L-FY 0.03
11T3008R-FY 0.08
11T3008L-FY 0.08
11T301R-FY 0.1
11T301L-FY 0.1
11T3018R-FY 0.18
11T3018L-FY 0.18
11T304R-FY 0.4
11T304L-FY 0.4
Boring
Bars
E
E32
SEC-Boring Bars
SDUC Type / SDQC Type
Inserts ( Coated carbide / Cermet / Carbide)
7 Positive G Class
DCGT Grades Dimensions (mm)
T1500Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
SD
Cat. No.
DCGT 070202R-SD
6.35 2.38
0.2
070202L-SD 0.2
070204R-SD 0.4
070204L-SD 0.4
DCGT 11T304R-SD
9.525 3.97
0.4
11T304L-SD 0.4
11T308R-SD 0.8
11T308L-SD 0.8
DCGT Grades Dimensions (mm)
H1
Inscribed circle
Thickness
Nose radius
AY
Cat. No.
DCGT 070201R-AY
6.35 2.38
0.1
070201L-AY 0.1
070202R-AY 0.2
070202L-AY 0.2
070204R-AY 0.4
070204L-AY 0.4
DCGT 11T301R-AY
9.525 3.97
0.1
11T301L-AY 0.1
11T302R-AY 0.2
11T302L-AY 0.2
11T304R-AY 0.4
11T304L-AY 0.4
7 Positive G Class
DCGW
Grades Dimensions (mm)
AC503U
Inscribed circle
Thickness
Nose radius
Cat. No.
DCGW 070202
6.35 2.38
0.2
070204 0.4
070208 0.8
DCGW 11T302
9.525 3.97
0.2
11T304 0.4
11T308 0.8
DCGT Grades Dimensions (mm)
AC610M
AC630M
AC510U
AC520U
AC1030U
AC530U
T1500Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
SI
Cat. No.
DCGT 070201MN-SI
6.35 2.38
0.1
070202MN-SI 0.2
070204MN-SI 0.4
DCGT 11T301MN-SI
9.525 3.97
0.1
11T302MN-SI 0.2
11T304MN-SI 0.4
11T308MN-SI 0.8
Nose radii with a sign "<" indicate negative tolerances.
DCGT Grades Dimensions (mm)
H1
Inscribed circle
Thickness
Nose radius
AG
Cat. No.
DCGT 070202N-AG 6.35 2.38 0.2
070204N-AG 0.4
DCGT 11T302N-AG
9.525 3.97
0.2
11T304N-AG 0.4
11T308N-AG 0.8
DCGT Grades Dimensions (mm)
AC1030U
AC530U
ACZ150
T1500Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
SC
Cat. No.
DCGT 0702003N-SC
6.35 2.38
0.03
DCGT 070201MN-SC
0.1
070202MN-SC
0.2
070204MN-SC
0.4
DCGT 11T3003N-SC
9.525 3.97
0.03
DCGT 11T301MN-SC
0.1
11T302MN-SC
0.2
11T304MN-SC
0.4
11T308MN-SC
0.8
Nose radii with a sign "<" indicate negative tolerances.
Boring
Bars
E33
E
SEC-Boring Bars
SDUC Type / SDQC Type
DCMT Grades Dimensions (mm)
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FB
Cat. No.
DCMT 070202N-FB
6.35 2.38
0.2
070204N-FB 0.4
070208N-FB 0.8
DCMT 11T302N-FB
9.525 3.97
0.2
11T304N-FB 0.4
11T308N-FB 0.8
Inserts (Coated carbide / Cermet / Carbide / SUMIBORON)
DCMT Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC630M
AC6030M
AC6040M
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
LU
Cat. No.
DCMT 070202N-LU 6.35 2.38 0.2
070204N-LU 0.4
DCMT 11T302N-LU
9.525 3.97
0.2
11T304N-LU 0.4
11T308N-LU 0.8
DCMT Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC830P
AC630M
AC6020M
AC6030M
AC405K
AC415K
AC420K
Inscribed circle
Thickness
Nose radius
MU
Cat. No.
DCMT 11T304N-MU 9.525 3.97 0.4
11T308N-MU 0.8
DCMW
Grades Dimensions (mm)
AC405K
AC415K
AC420K
Inscribed circle
Thickness
Nose radius
Cat. No.
DCMW 070204 6.35 2.38 0.4
070208 0.8
DCMW 11T304 9.525 3.97 0.4
11T308 0.8
DCMT Grades Dimensions (mm)
AC820P
AC8025P
AC830P
AC6020M
AC6030M
AC6040M
T1500Z
T3000Z
T1500A
Inscribed circle
Thickness
Nose radius
LB
Cat. No.
DCMT 070202N-LB
6.35 2.38
0.2
070204N-LB 0.4
070208N-LB 0.8
DCMT 11T302N-LB
9.525 3.97
0.2
11T304N-LB 0.4
11T308N-LB 0.8
DCMT
Grades
Dimensions (mm)
AC810P
AC820P
AC8025P
AC830P
AC610M
AC630M
AC6020M
AC6030M
AC6040M
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
SU
Cat. No.
DCMT 070202N-SU
6.35
2.38
0.2
070204N-SU
0.4
070208N-SU
0.8
DCMT 11T302N-SU
9.525
3.97
0.2
11T304N-SU
0.4
11T308N-SU
0.8
DCMT
Grades Dimensions (mm)
T1500A
Inscribed circle
Thickness
Nose radius
FP
Cat. No.
DCMT 070202N-FP 6.35 2.38 0.2
070204N-FP 0.4
DCMT 11T308N-FP 9.525 3.97 0.8
7 Positive G Class
SUMIBORON Multi Corner One Use Inserts (Coated)
2NC-
DCGW
Grades Dimensions (mm)
BNC2010
BNC2020
BNC100
BNC160
BNC200
BNC300
BNC500
Inscribed circle
Thickness
Nose radius
Cat. No.
2NC-DCGW 070202
6.35 2.38
0.2
070204 0.4
070208 0.8
070202LT 0.2
070204LT 0.4
070202LS 0.2
070204LS 0.4
2NC-DCGW 11T302
9.525 3.97
0.2
11T304 0.4
11T308 0.8
11T304-WG 0.4
11T308-WG 0.8
11T304-WH 0.4
11T308-WH 0.8
2NC-DCGW 11T302LE
9.525 3.18
0.2
11T304LE 0.4
11T308LE 0.8
11T302LT 0.2
11T304LT 0.4
11T308LT 0.8
2NC-DCGW 11T302LS
9.525 3.97
0.2
11T304LS 0.4
11T308LS 0.8
11T304HS 0.4
11T308HS 0.8
Note: The part number suffixes stand for the following: WG/WH: Wiper insert LE: Low resistance type
LT/LS: Cutting performance focused type HS: Strengthened cutting edge type
7 Positive M Class
SUMIBORON Break Master (Coated)
2NC-
DCGT
Grades Dimensions (mm)
BNC2010
BNC2020
BNC160
BNC200
Inscribed circle
Thickness
Nose radius
FV/LV
Cat. No.
2NC-DCGT 070204N-FV 6.35 2.38 0.4
2NC-DCGT 11T304N-FV
9.525 3.97
0.4
11T308N-FV 0.8
11T304N-LV 0.4
11T308N-LV 0.8
Boring
Bars
E34
E
SEC-Boring Bars
SDUC Type / SDQC Type
mark: To be replaced by new item (Please confirm stock availability)
Inserts (SUMIBORON / SUMIDIA)
7 Positive G Class
SUMIBORON One Use Inserts (Non-Coated)
(D mark: Only packages containing one piece are in stock, A mark: Packages containing one piece and packages containing 10 pieces are in stock)
NU-
DCGW
Grades Dimensions (mm)
BN1000
BN2000
BN7000
BN700
Inscribed circle
Thickness
Nose radius
Cat. No.
NU-DCGW 070202
6.35 2.38
0.2
070204 0.4
070208 0.8
070202LT 0.2
070204LT 0.4
070208LT 0.8
070202HS 0.2
070204HS 0.4
NU-DCGW 11T302
9.525 3.97
0.2
11T304 0.4
11T308 0.8
11T312 1. 2
11T302LF 0.2
11T304LF 0.4
11T302LT 0.2
11T304LT 0.4
11T308LT 0.8
11T312LT 1. 2
11T312LS 1. 2
11T302HS 0.2
11T304HS 0.4
11T308HS 0.8
Note: The part number suffixes stand for the following: LF: Sharp edge LT/LS: Cutting performance focused
type HS: Strengthened cutting edge type
7 Positive G Class
SUMIDIA NF Inserts
NF-
DCMT
Grades Dimensions (mm)
DA1000
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
NF-DCMT 070201
6.35 2.38
0.1
070202 0.2
070204 0.4
NF-DCMT 11T301
9.525 3.97
0.1
11T302 0.2
11T304 0.4
11T308 0.8
SUMIDIA Break Master
NF-
DCMT
Grades Dimensions (mm)
DA1000
Inscribed circle
Thickness
Nose radius
LD/GD
Cat. No.
NF-DCMT 070202N-LD
6.35 2.38
0.2
070204N-LD 0.4
070202N-GD 0.2
070204N-GD 0.4
NF-DCMT 11T302N-LD
9.525 3.97
0.2
11T304N-LD 0.4
11T308N-LD 0.8
11T302N-GD 0.2
11T304N-GD 0.4
11T308N-GD 0.8
Note: The part number suffixes stand for the following: LD: For finishing GD: For medium finishing
SUMIDIA
DCMT Grades Dimensions (mm)
DA150
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
DCMT 070201
6.35 2.38
0.1
070202 0.2
070204 0.4
DCMT 11T301
9.525 3.97
0.1
11T302 0.2
11T304 0.4
SUMIDIA Binderless
DCMW
Grades Dimensions (mm)
NPD10
Inscribed circle
Thickness
Nose radius
Cat. No.
DCMW 070202RH 6.35 2.38 0.2
070204RH 0.4
DCMW 11T302RH
9.525 3.97
0.2
11T304RH 0.4
11T308RH 0.8
SUMIBORON Multi Corner One Use Inserts (Non-Coated)
(D mark: Only packages containing one piece are in stock, A mark: Packages containing one piece and packages containing 10 pieces are in stock)
2NU-
DCGW
Grades Dimensions (mm)
BN2000
BN7000
BN7500
Inscribed circle
Thickness
Nose radius
Cat. No.
2NU-DCGW 070204 6.35 2.38 0.4
070208 0.8
2NU-DCGW 11T302
9.525 3.97
0.2
11T304 0.4
11T308 0.8
11T304WG 0.4
11T308WG 0.8
11T304WH 0.4
11T308WH 0.8
11T302LF 0.2
11T304LF 0.4
11T308LF 0.8
11T302LE 0.2
11T304LE 0.4
11T308LE 0.8
11T302LS 0.2
11T304LS 0.4
11T308LS 0.8
Note: The part number suffixes stand for the following: WG/WH: Wiper insert LF/LE:
Sharp edge LS: Cutting performance focused type
SUMIBORON Break Master (Non-Coated)
2NU-
DCGT
Grades Dimensions (mm)
BN2000
Inscribed circle
Thickness
Nose radius
FV/LV
Cat. No.
2NU-DCGT 070204N-FV 6.35 2.38 0.4
2NU-DCGT 11T304N-FV
9.525 3.97
0.4
11T308N-FV 0.8
11T304N-LV 0.4
11T308N-LV 0.8
Boring
Bars
E35
E
Profiling
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat.
No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Offset
Applicable inserts Clamp
set
Wrench for
upper surface
Wrench for
lower surface
RL
DMIN
DCON
HLFWFLHE1 Cat. No. Page
Steel
S32T-DDQN R/L1504-40 S32T-DDQN R/L15
40 32 30 300 22 48 6
DN 1504
From
B32 SCP-2 5.0 LH040 LH025
S-DDQN
Profiling
Steel
– 6°
–12°
107.5°
DCON
LF
LH
WF
E1
H
DMIN Min.
machinable diameter
Inserts
DNMG150408N-GE
SEC-Boring Bars
S-DDQN Type / S-DDUN Type / D-DDUN Type
107.5°
93˚
S-DDUN
Profiling
Steel
Fig 1
93°
-6°
-12°
DCON
LF
LH
WF
E1
H
DMIN Min.
machinable diameter
Fig 2
93°
-6°
DCON
DMIN Min.
machinable diameter
LF
WF
E1
H
D-DDUN
Profiling Oil hole
Steel with
vibration
control
mechanism
93°
– 6°
DCON
GAMF
LF
LH
WF
H
DMIN Min.
machinable diameter
Parts
Holders
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Offset
Fig Applicable inserts Clamp
set Shim
Screw for
shim
Wrench for
upper surface
Wrench for
lower surface
RL
DMIN
DCON
HLFWFLHE1 Cat. No.
Page
Steel
S32S-DDUN R/L1504-40
40 32 30 250 22.0 26 7.0 1
DN 1504
From
B32 SCP-2 5.0
DNS1504B
BFTX0409N
LH040 LH025
S40T-DDUN R/L1504-50
50 40 37 300 27.0 26 8.5
S50U-DDUN R/L1504-63
63 50 47 350 31.5 8.0 2
Parts
Holders
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Applicable inserts Clamp
sets Shims Screws
for shim
Wrenches for
upper surface
Wrenches for
lower surface
RL
DMIN
DCON
HLFWFLH
GAMF
Cat. No.
Page
Vibration control
mechanism
steel with oil hole
D32T-DDUN R/L1104-40
40 32 30 300 22 26
10 DN 110 4
From
B31 SCP-1 5.0
DNS1104B
BFTX0307N
LH040 LH025
D32T-DDUN R/L1506-40
40 32 30 300 22 26
12 DN 1506
From
B36 SCP-2 5.0
DNS1506B
BFTX0409N
LH040 LH025
D40U-DDUN R/L1506-50
50 40 37 350 27 26
12
Inserts
DNMG110404N-GU
DNMG150604N-GE
Parts for clamp set
E81
Parts for clamp set
E81
Parts for clamp set
E81
Recommended tightning torque(N m) mark: Standard stocked item (expanded product)
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
Boring
Bars
E36
E
S-PDUN
Profiling
Steel
Fig 1 Fig 2
-6°
93°
DCON
GAMF
LH
LF
WF
H
DMIN Min.
machinable diameter
-6°
93°
DCON
GAMF
LF
WF
E1
H
DMIN Min.
machinable diameter
Profiling
Inserts
DNMG150408N-GE
(Representative example)
S-EDUN
Profiling
Steel
93°
– 5°
DCON
GAMF
LF
LH
WF
E1
H
DMIN Min.
machinable diameter
SEC-Boring Bars
S-PDUN Type / S-EDUN Type
93˚
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Conventional
Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Offset
Rake
angle Fig Applicable inserts Lever
pins Bolts Shims
Shims
retainer
Wrenches
RL
DMIN
DCON
HLF
WF
LH E1
GAMF
Cat. No. Page
Steel
S25R-PDUN R/L1104-32
32 25 22 200
17.0
20 7.0
15
1
DN 110 4
From
B31 LCL3 LCS3
LSD317
LSP3 LH025
S32S-PDUN R/L1504-40
40 32 30 250
22.0
20 7.0
12
1
DN 1504
From
B32 LCL4 LCS4 LSD42 LSP4 LH030
S32S-PDUN R/L1504-44
S32S-PDUN R/L15
44 32 30 250
22.0
20 7.0
10
S40T-PDUN R/L1504-50
50 40 37 300
27.0
20 8.5
12
S50U-PDUN R/L1504-63
63 50 47 350
31.5
8.0
12
2
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Offset
Rake
angle Applicable inserts Shims Eccentric
shafts
Wrenches
RL
DMIN
DCON
HLF
WF
LH E1
GAMF
Cat. No. Page
Steel
S25R-EDUN R/L1104-34
BDUN325 R/L 34 25 23 200 17 20 5.5
12
DN 110 4
From
B31 SDW323 CPB34 LH025
S32S-EDUN R/L1504-44
BDUN432 R/L 44 32 30 250 22 20 7.0
10
DN 1504
From
B32 SDW423 CPB43 LH030
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
mark: Standard stocked item (expanded product)
Boring
Bars
E37
E
SEC-Boring Bars
S-PDZN Type / S-EDZN Type / S-DTR55C Type
Parts
Holders Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts.
Left handed (L) holders are applicable for left handed (L) and neutral (N) inserts.
Holder
Material
Cat. No. Conventional
Cat. No.
Stock
Min. machining
diameter
Diameter Height Length
Cutting edge
distance
Offset Fig Applicable inserts Lever
pin Bolt Shim
Shim
retainer
Wrenches
RL
DMIN
DCON
HLFWFE1 Cat. No. Page
Steel
S32S-PDZN R/L1504-40
40 32 30 250 22.0 7.0 2
DN 1504
From
B32 LCL4 LCS4 LSD42 LSP4 LH030
S32S-PDZN R/L1504-44
S32S-PDZN R/L15
44 32 30 250 22.0 7.0 1
S40T-PDZN R/L1504-50
50 40 37 300 27.0 8.5 2
S50U-PDZN R/L1504-63
63 50 47 350 31.5 8.0 3
Inserts
DNMG150408N-GE
(Representative example)
S-PDZN
Profiling
Steel
Fig1
-6°
26
93°
-12°
DCON
LF
25
WF
E1
H
DMIN Min.
machinable diameter
Profiling
Inserts
DNMG150408N-GE
(Representative example)
Parts
Holders
Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts.
Left handed (L) holders are applicable for left handed (L) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset
Rake
angle Applicable inserts Shims Eccentric
shafts
Wrenches
RL
DMIN
DCON
HLFWFE1
GAMF
Cat. No. Page
Steel
S25R-EDZN R/L1104-34
BDZN325 R/L 34 25 23 200 17 5.5
12
DN 110 4
From
B31 SDW323 CPB34 LH025
S32S-EDZN R/L1504-44
BDZN432 R/L 44 32 30 250 22 7.0
10
DN 1504
From
B32 SDW423 CPB43 LH030
S-EDZN
Profiling
Steel
20(25)
93°
–5°
DCON
GAMF
LF
WF
E1
H
DMIN Min.
machinable diameter
Internal Profiling
-5
93
DCON
GAMF LF
LH
HF WF
E1
H
DMIN Min.
machinable diameter
S-DTR55C
Internal Profiling
Parts
Holders
Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle
Offset
Cutting edge
height
Clamp Spring
Cap screw
Shim Screw for
shim Wrench Wrench
for shim
R
DMIN
DCON
HLFWFLH
GAMF
E1 HF
S32S-DTR55C R-17
44 32 30 250 22 42 12 7.0 15.0 TRCP3
S-SP4-20
BX0520 3.5–4.5
TRW5505
BFTX0307N
TSW040
TRX10
S40T-DTR55C R-17
50 40 37 300 25 42 10 6.2 18.5
* Not included with the product.
Steel
Inserts
See: C12
TRM551708-GU
(Representative example)
93° 93˚
(For Torx holes)
(For hexagonal holes)
-6°
Fig2
–5°
Fig3
Recommended tightning torque(N m) mark: Standard stocked item (expanded product)
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
Boring
Bars
E38
E
Internal Profiling
SEC-Boring Bars
S-SVJB Type / B-SVJB Type / S-SVJC Type
93°
Recommended tightning torque(N m)
mark: Standard stocked item (expanded product)
Holders
Parts
Holder
Material
Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head Rake
angle Fig Applicable inserts
Cat. No. Screws
Wrenches
RL
DMIN
DCON
HLFWFLH
LH3
GAMF
Steel
S20R-SVJB R/L1103-25 25 20 19 200 2.0 42 29 1VB110 3
BFTX02508NV
1. 5 TRX08
S25S-SVJB R/L1103-30 30 25 24 250 3.5 50 36
S32T-SVJB R/L1604-40 40 32 30 300 3.5 75 60 82VB1604
BFTX03508
2.0 TRX10
S40T-SVJB R/L1604-50 50 40 37 300 4.5 95 75 7
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
52°
93°
– 5°
– 5°
DCON
WF
LF
LH3
LH H
DMIN Min.
machinable diameter
Parts
Holders
Holder
Material
Cat. No.
Stock
Min. machining
diameter
Diameter
Height Length
Cutting edge
distance
Head Applicable inserts
Cat. No. Screw Wrench
RL
DMIN
DCON
HLFWFLH
LH3
Steel with
vibration
control
mechanism
B20R-SVJB R/L1103-25
25 20 19 200 2.0 55 37.5 VB 110 3
BFTX02508NV
1. 5 TRX08
B25S-SVJB R/L1103-30
30 25 24 250 3.5 62 45
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
52°
– 5°
– 5°
DCON
LF
LH3
LH
WF
H
DMIN Min.
machinable diameter
93°
Concave Facing
/ Hole Bottom Facing
S-SVJB
Concave Facing
/ Hole Bottom Facing
B-SVJB
Steel
Steel with
vibration
control
mechanism
Parts
Holders
Holder
Material
Cat. No.
Stock
Min. machining
diameter
Diameter
Height Length
Cutting edge
distance
Head
Applicable inserts Screw Wrench
RL
DMIN
DCON
HLFWFLH
LH3
Steel
S12M-SVJC R/L0802-16
16 12 11 150 2.0 30 21 VC 0802
BFTX0204N
0.5 TRX06
S16Q-SVJC R/L0802-20
20 16 15 180 2.0 40 29
52°
93°
– 5°
– 5°
DCON
LF
LH3
LH
WF
H
DMIN Min.
machinable diameter
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Concave Facing
/ Hole Bottom Facing
S-SVJC
Steel
(For Torx holes)
(For Torx holes)
(For Torx holes)
52°
93°
– 5°
DCON
GAMF
WF
LF
LH3
LH H
DMIN Min.
machinable diameter
Fig 1 Fig 2
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
Boring
Bars
E39
E
SEC-Boring Bars
S-SVQB Type / B-SVQB Type / C-SVQB Type
108°
Internal Profiling
Parts
Holders
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset
Applicable
inserts Pins Bolt Shim Screws
Wrenches
Wrench
for bolt
RL
DMIN
DCON
HLFWFE1
Steel
S20R-SVQB R/L1103-25 25 20 18 200
14.5 5.5
VB 110 3
BFTX02508NV
1. 5 TRX08
S25S-SVQB R/L1103-32 32 25 23 250
19.0 7.5
S25S-SVQB R/L1604-34 34 25 23 250
20.5 9.0
VB 1604
BFTX03508
2.0 TRX10
S32T-SVQB R/L1604-40 40 32 30 300
22.0 9.0
VP32B
BH03504
SVP32 LH020
S40T-SVQB R/L1604-50 50 40 37 300
27.0 10.0
VP40B
(For Torx holes)
(– 4.5°)
– 6.5°
108°
35°
DCON
LF H
WF
E1
DMIN Min.
machinable diameter
Steel
S-SVQB
Profiling
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height Length
Cutting edge
distance
Offset
Applicable inserts Screw Wrench
RL
DMIN
DCON
HLFWFE1
Steel with
vibration control
mechanism
B16R-SVQB R/L1103-20 20 16 15 200 11.5 4 VB 110 3
BFTX02508NV
1. 5 TRX08
B20R-SVQB R/L1103-25 25 20 18 200 14.5 5
(For Torx holes)
B-SVQB
Profiling
Steel with
vibration
control
mechanism
(– 4.5°)
– 6.5°
108°
35°
DCON
LF
WF
E1
H
DMIN Min.
machinable diameter
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height Length
Cutting edge
distance
Offset Applicable inserts Screw Wrench
RL
DMIN
DCON
HLFWFE1
Carbide
C16R-SVQB R/L1103-20 20 16 15 200 11.5 4 VB 110 3
BFTX02508NV
1. 5 TRX08
C20R-SVQB R/L1103-25 25 20 18 200 14.5 5
(For Torx holes)
Profiling
C-SVQB
Carbide
(– 4.5°)
– 6.5°
108°
35°
WF
E1
LF
H
DCON
DMIN Min.
machinable diameter
Recommended tightning torque(N m) mark: Standard stocked item (expanded product)
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
Boring
Bars
E40
E
Recommended tightning torque (N m) mark: Standard stocked item (expanded product) mark: To be replaced by new item (Please confirm stock availability)
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFE1
Steel
with oil
hole
A16Q-SVQC R/L1103-20 20 16 15 180
11. 5
4.5
VC 110 3
BFTX02508NV
1. 5 TRX08
A20R-SVQC R/L1103-25 25 20 18 200
14.5
5.5
A25S-SVQC R/L1103-32 32 25 23 250
19.0
7. 5
A25S-SVQC R/L1604-34 34 25 23 250
20.5
9.0 VC 1604
BFTX03508
2.0 TRX10
(For Torx holes)
A-SVQC
Profiling
SEC-Boring Bars
S-SVQC Type / A-SVQC Type
This figure shows right handed tools.
Dimensions (mm)
Steel
Oil hole
LF
(– 4.5°)
– 6.5°
108°
WF
E1
H
DCON
DMIN Min.
machinable diameter With oil hole
108°
Internal Profiling
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Conventional
Cat. No.
Stock
Min. machining
diameter
Diameter Height
Length
Cutting edge
distance
Offset
Applicable
inserts Pins Bolt Shim Screws
Wrenches
Wrench
for bolt
RL
DMIN
DCON
HLFWFE1
Steel
S10M-SVQC R/L0802-14
14 10 9 150
8.5 4.5
VC 0802
BFTX0204N
0.5 TRX06
S12M-SVQC R/L0802-16
16 12 11 150
9.5 4.5
S16Q-SVQC R/L1103-20
20 16 15 180
11.5 4.5
VC 110 3
BFTX02508NV
1. 5 TRX08
S25R-SVQC R/L1604-35
S25R-SVQC R/L16
35 25 23 200
20.5 9.0
VC 1604
BFTX03508
2.0 TRX10
S32S-SVQC R/L1604-40
S32S-SVQC R/L16
40 32 30 250
22.0 9.0
VP32B
BH03504
SVP32 LH020
S40T-SVQC R/L1604-50
S40T-SVQC R/L16
50 40 37 300
27.0 10.0
VP40B
(For Torx holes)
(– 4.5°)
– 6.5°
108°
35°
DCON
LF H
WF
E1
DMIN Min.
machinable diameter
Steel
S-SVQC
Profiling
This figure shows right handed tools.
Dimensions (mm)
Boring
Bars
E41
E
Internal Profiling
SEC-Boring Bars
S-SVUB Type / B-SVUB Type / C-SVUB Type
93˚
Recommended tightning torque(N m) mark: Standard stocked item (expanded product)
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset Applicable inserts Screw Wrench
RL
DMIN
DCON
HLFWFE1
Steel with vibration
control mechanism
B12M-SVUB R/L1103-20 20 12 11 150 13.5 8 VB 110 3
BFTX02508NV
1. 5 TRX08
B16R-SVUB R/L1103-25 25 16 15 200 16.5 9
(For Torx holes)
B-SVUB
Profiling
Steel with
vibration
control
mechanism
(– 2.5°)
93°
– 7.5° 35°
DCON
LF
WF
E1
H
DMIN Min.
machinable diameter
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset Applicable inserts Screw Wrench
RL
DMIN
DCON
HLFWFE1
Carbide
C12M-SVUB R/L1103-20 20 12 11 150 13.5 8 VB 110 3
BFTX02508NV
1. 5 TRX08
C16R-SVUB R/L1103-25 25 16 15 200 16.5 9
(For Torx holes)
Carbide
Profiling
C-SVUB
(– 2.5°)
93°
– 7.5° 35°
DCON
LF
WF
E1
H
DMIN Min.
machinable diameter
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
93°
DCON
GAMF
GAMP
LF
WF
E1
H
DMIN Min.
machinable diameter
93°
DCON
GAMF
GAMP
LF
WF
E1
H
DMIN Min.
machinable diameter
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset
Rake angle
Fig Applicable
inserts Pins Bolt Shim Screws
Wrenches
Wrench
for bolt
RL
DMIN
DCON
HLFWFE1
GAMF GAMP
Steel
S20R-SVUB R/L1103-28
28 20 18 200
17.5 7.5
7. 5 3.0
1
VB 110 3
BFTX02508NV
1. 5 TRX08
S25S-SVUB R/L1103-32
32 25 23 250
19.0 7.5
6.5 2.5
2
S25S-SVUB R/L1604-34
34 25 23 250
20.5 9.0
7. 5 3.0
2
VB 1604
BFTX03508
2.0 TRX10
S32T-SVUB R/L1604-40
40 32 30 300
23.5 10.5
3VP32B
BH03504
SVP32 LH020
S40T-SVUB R/L1604-50
50 40 37 300
29.5 12.5
VP40B
(For Torx holes)
Fig3
Fig1 Fig2
S-SVUB
Profiling
Steel
This figure shows right handed tools.
Dimensions (mm)
Boring
Bars
E
E42
SEC-Boring Bars
S-SVUC Type / A-SVUC Type
93˚
Parts
Holders
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Conventional
Cat. No.
Stock
Min. machining
diameter
Diameter
Height Length
Cutting edge
distance
Head
Off set
Fig
Applicable
inserts
Pins Bolt Shim Screws
Wrenches
Wrench
for bolt
RL
DMIN
DCON
HLF
WF
LH E1
Steel
S12M-SVUC R/L0802-16
16 12 11 150
9.5
6.5
3.5
1
VC 0802
BFTX0204N
0.5 TRX06
S16Q-SVUC R/L0802-20
20 16 15 180
11. 5 3.5
2
S16Q-SVUC R/L1103-25
25 16 15 180
16.5 8.5
2
VC 110 3
BFTX02508NV
1. 5 TRX08
S25R-SVUC R/L1604-35
S25R-SVUC R/L16
35 25 23 200
20.5 9.0
3
VC 1604
BFTX03508
2.0 TRX10
S32S-SVUC R/L1604-40
S32S-SVUC R/L16
40 32 30 250
22.0 9.0
VP32B
BH03504
SVP32 LH020
S40T-SVUC R/L1604-50
S40T-SVUC R/L16
50 40 37 300
27.0 10.0
VP40B
(For Torx holes)
Fig3
(– 3°)
93°
– 7.5° (– 3°)
DCON
LF
LH
WF
E1
H
DMIN Min.
machinable diameter
Fig1
93°
(– 3°)
– 7.5°
DCON
LF
WF
E1
H
DMIN Min.
machinable diameter
Fig2
S-SVUC
Profiling
Steel
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height Length
Cutting edge
distance
Offset
Rake angle
Applicable inserts Screws Wrenches
RL
DMIN
DCON
HLFWFE1
GAMF GAMP
Steel with oil
hole
A16Q-SVUC R/L1103-25 25 16 15 180
16.5
8.5
7. 5 3.0
VC 110 3
BFTX02508NV
1. 5 TRX08
A20R-SVUC R/L1103-28 28 20 18 200
17.5
7. 5
7. 5 3.0
A25S-SVUC R/L1103-32 32 25 23 250
19.0
7. 5
6.5 2.5
A25S-SVUC R/L1604-34 34 25 23 250
20.5
9.0
7. 5 3.0
VC 1604
BFTX03508
2.0 TRX10
(For Torx holes)
A-SVUC
Profiling
Recommended tightning torque (N m) mark: Standard stocked item (expanded product) mark: To be replaced by new item (Please confirm stock availability)
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
Steel
Oil hole 93°
E1
WF
H
DCON
LF
GAMP
GAMF
DMIN Min.
machinable diameter
With oil hole
Boring
Bars
E43
E
Holders Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts.
Left handed (L) holders are applicable for left handed (L) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset Applicable inserts Screw Wrench
RL
DMIN
DCON
HLFWFE1
Carbide
C12M-SVZB R/L1103-20 20 12 11 150 13.5 8 VB 1103
BFTX02508NV
1. 5 TRX08
C16R-SVZB R/L1103-25 25 16 15 200 16.5 9
Parts
Holders Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts.
Left handed (L) holders are applicable for left handed (L) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Head
Cutting edge
distance
Offset
Applicable inserts
Pins Bolt Shim Screws
Wrenches
Wrench
for bolt
RL
DMIN
DCON
HLFLHWFE1
Steel
S20R-SVZB R/L1103-25
25 20 18 200 15
14.5 5.5
VB 110 3
BFTX02508NV
1. 5 TRX08
S25S-SVZB R/L1103-32
32 25 23 250 15
19.0 7.5
S25S-SVZB R/L1604-34
34 25 23 250 20
20.5 9.0
VB 1604
BFTX03508
2.0 TRX10
S32T-SVZB R/L1604-40
40 32 30 300 20
22.0 9.0
VP32B
BH03504
SVP32 LH020
S40T-SVZB R/L1604-50
50 40 37 300 20
27.0 10.0
VP40B
Holders Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts.
Left handed (L) holders are applicable for left handed (L) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Offset Applicable inserts Screw Wrench
RL
DMIN
DCON
HLFWFE1
Steel with
vibration control
mechanism
B12M-SVZB R/L1103-20 20 12 11 150 13.5 8 VB 1103
BFTX02508NV
1. 5 TRX08
B16R-SVZB R/L1103-25 25 16 15 200 16.5 9
SEC-Boring Bars
S-SVZB Type / B-SVZB Type / C-SVZB Type
Internal Profiling
B-SVZB
Profiling
Steel with
vibration
control
mechanism
WF
15
– 7.5°
93°
35°
(–2.5°)
DCON
LF
E1
H
DMIN Min.
machinable diameter
Profiling
C-SVZB
Carbide
WF
15
– 7.5°
93°
35°
(–2.5°)
DCON
LF
E1
H
DMIN Min.
machinable diameter
Steel
93°
(For Torx holes)
(For Torx holes)
(For Torx holes)
Recommended tightning torque(N m) mark: Standard stocked item (expanded product)
S-SVZB
Profiling
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
– 7.5°
0°
93°
35°
DCON
LF
LH
WF
E1
H
DMIN Min.
machinable diameter
Boring
Bars
E44
E
Parts
Holders Right-handed (R) holders are applicable for right-handed (R) and neutral (N) inserts.
Left handed (L) holders are applicable for left handed (L) and neutral (N) inserts.
Holder
Material
Cat. No. Conventional
Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Head
Cutting edge
distance
Offset
Applicable
inserts Pins Bolt Shim Screws
Wrenches
Wrench
for bolt
RL
DMIN
DCON
HLFLHWFE1
Steel
S12M-SVZC R/L0802-16
16 12 11 150 10
9.5 4.5
VC 0802
BFTX0204N
0.5 TRX06
S16Q-SVZC R/L1103-20
20 16 15 180 15
11.5 4.5
VC 110 3
BFTX02508NV
1. 5 TRX08
S25R-SVZC R/L1604-35
S25R-SVZC R/L16
35 25 23 200 20
20.5 9.0
VC 1604
BFTX03508
2.0 TRX10
S32S-SVZC R/L1604-40
S32S-SVZC R/L16
40 32 30 250 20
22.0 9.0
VP32B
BH03504
SVP32 LH020
S40T-SVZC R/L1604-50
S40T-SVZC R/L16
50 40 37 300 20
27.0 10.0
VP40B
Steel
– 7.5°
0°
93°
35°
LH
DCON
LF
WF
E1
H
DMIN Min.
machinable diameter
SEC-Boring Bar
S-SVZC Type
93°
(For Torx holes)
Recommended tightning torque (N m) mark: Standard stocked item (expanded product) mark: To be replaced by new item (Please confirm stock availability)
S-SVZC
Profiling
This figure shows right handed tools.
Dimensions (mm)
Boring
Bars
E45
E
SEC-Boring Bars
SVJB Type / SVQB Type / SVUB Type / SVZB Type
Inserts ( Coated carbide / Cermet / Carbide)
5 Positive G Class
VBGT Grades Dimensions (mm)
AC1030U
AC530U
T1500Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FX
Cat. No.
VBGT 110301R-FX
6.35 3.18
0.1
110301L-FX 0.1
110302R-FX 0.2
110302L-FX 0.2
110304R-FX 0.4
110304L-FX 0.4
VBGT 160402R-FX
9.525 4.76
0.2
160402L-FX 0.2
160404R-FX 0.4
160404L-FX 0.4
VBGT Grades Dimensions (mm)
AC1030U
Inscribed circle
Thickness
Nose radius
FYS
Cat. No.
VBGT 1103003R-FYS
6.35 3.18
0.03
1103003L-FYS 0.03
110301R-FYS 0.1
110301L-FYS 0.1
110302R-FYS 0.2
110302L-FYS 0.2
110304R-FYS 0.4
110304L-FYS 0.4
110308R-FYS 0.8
110308L-FYS 0.8
VBGT Grades Dimensions (mm)
AC1030U
AC530U
T1500Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FY
Cat. No.
VBGT 110301R-FY
6.35 3.18
0.1
110301L-FY 0.1
110302R-FY 0.2
110302L-FY 0.2
110304R-FY 0.4
110304L-FY 0.4
VBGT Grades Dimensions (mm)
AC510U
AC520U
AC1030U
AC530U
Inscribed circle
Thickness
Nose radius
SI
Cat. No.
VBGT 110301MN-SI
6.35 3.18
0.1
110302MN-SI 0.2
110304MN-SI 0.4
110308MN-SI 0.8
160401MN-SI
9.525 4.76
0.1
160402MN-SI 0.2
160404MN-SI 0.4
160408MN-SI 0.8
Nose radii with a sign "<" indicate negative tolerances.
5 Positive G Class
VBGT Grades Dimensions (mm)
H1
Inscribed circle
Thickness
Nose radius
AY
Cat. No.
VBGT 110301R-AY
6.35 3.18
0.1
110301L-AY 0.1
110302R-AY 0.2
110302L-AY 0.2
110304R-AY 0.4
110304L-AY 0.4
VBGT 160402R-AY
9.525 4.76
0.2
160402L-AY 0.2
160404R-AY 0.4
160404L-AY 0.4
5 Positive M Class
VBMT Grades Dimensions (mm)
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FB
Cat. No.
VBMT 110302N-FB
6.35 3.18
0.2
110304N-FB 0.4
110308N-FB 0.8
VBMT 160404N-FB 9.525 4.76 0.4
160408N-FB 0.8
VBMT
Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC630M
AC6030M
AC6040M
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
LU
Cat. No.
VBMT 110302N-LU
6.35 3.18
0.2
110304N-LU 0.4
110308N-LU 0.8
VBMT 160404N-LU 9.525 4.76 0.4
160408N-LU 0.8
VBMT
Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC830P
AC610M
AC630M
AC6020M
AC6030M
AC6040M
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
SU
Cat. No.
VBMT 110302N-SU
6.35 3.18
0.2
110304N-SU 0.4
110308N-SU 0.8
VBMT 160404N-SU
9.525 4.76
0.4
160408N-SU 0.8
160412N-SU 1. 2
VBMW
Grades Dimensions (mm)
AC405K
AC415K
AC420K
Inscribed circle
Thickness
Nose radius
Cat. No.
VBMW 160404 9.525 4.76 0.4
160408 0.8
VBMT Grades Dimensions (mm)
AC820P
AC8025P
AC830P
AC6020M
AC6030M
AC6040M
T1500Z
T3000Z
T1500A
Inscribed circle
Thickness
Nose radius
LB
Cat. No.
VBMT 110302N-LB
6.35 3.18
0.2
110304N-LB 0.4
110308N-LB 0.8
VBMT 160404N-LB
9.525 4.76
0.4
160408N-LB 0.8
160412N-LB 1. 2
Boring
Bars
E46
E
Inserts (SUMIBORON)
SEC-Boring Bars
SVJB Type / SVQB Type / SVUB Type / SVZB Type
SUMIBORON One Use Inserts (Non-Coated)
NU-
VBGW
Grades Dimensions (mm)
BN1000
BN2000
BN7000
BN700
Inscribed circle
Thickness
Nose radius
Cat. No.
NU-VBGW 110302
6.35 2.38
0.2
110304 0.4
110308 0.8
110302LT 0.2
110304LT 0.4
110308LT 0.8
110302HS 0.2
110304HS 0.4
110308HS 0.8
NU-VBGW 160402
9.525 4.76
0.2
160404 0.4
160408 0.8
160402LT 0.2
160404LT 0.4
160408LT 0.8
160404HS 0.4
160408HS 0.8
Note: The part number suffixes stand for the following: LT: Cutting performance focused type HS: Strengthened cutting edge type
5 Positive G Class
SUMIBORON Multi Corner One Use Inserts (Coated)
2NC-
VBGW
Grades Dimensions (mm)
BNC2010
BNC2020
BNC500
Inscribed circle
Thickness
Nose radius
Cat. No.
2NC-VBGW 110302
6.35 2.38
0.2
110304 0.4
110308 0.8
110302LT 0.2
110304LT 0.4
2NC-VBGW 160402
9.525 4.76
0.2
160404 0.4
160408 0.8
160402LE 0.2
160404LE 0.4
160408LE 0.8
160402LT 0.2
160404LT 0.4
160408LT 0.8
Note: The part number suffixes stand for the following: LE: Low resistance type LT: Cutting performance focused type
SUMIBORON Multi Corner One Use Inserts (Non-Coated)
2NU-
VBGW
Grades Dimensions (mm)
BN7000
Inscribed circle
Thickness
Nose radius
Cat. No.
2NU-VBGW 110304 6.35 3.18 0.4
110308 0.8
2NU-VBGW 160404 9.525 4.76 0.4
160408 0.8
Boring
Bars
E47
E
Inserts ( Coated carbide / Cermet / Carbide)
VCGT Grades Dimensions (mm)
H1
Inscribed circle
Thickness
Nose radius
AW
Cat. No.
VCGT 160408N-AW 9.525 4.76 0.8
160412N-AW 1. 2
VCGT Grades Dimensions (mm)
H1
Inscribed circle
Thickness
Nose radius
AG
Cat. No.
VCGT 110302N-AG 6.35 3.18 0.2
110304N-AG 0.4
VCGT 160408N-AG 9.525 4.76 0.8
160412N-AG 1. 2
VCMT Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC630M
AC6030M
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
LU
Cat. No.
VCMT 160404N-LU 9.525 4.76 0.4
160408N-LU 0.8
7 Positive M Class
VCMT Grades Dimensions (mm)
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FB
Cat. No.
VCMT 080202N-FB 4.76 2.38 0.2
080204N-FB 0.4
VCMT 160404N-FB 9.525 4.76 0.4
160408N-FB 0.8
7 Positive E Class
VCET Grades Dimensions (mm)
ACZ150
Inscribed circle
Thickness
Nose radius
FX
Cat. No.
VCET 1103008R-FX
6.35 3.18
0.08
1103008L-FX 0.08
110301R-FX 0.1
110301L-FX 0.1
1103018R-FX 0.18
1103018L-FX 0.18
VCGT Grades Dimensions (mm)
AC520U
AC1030U
AC530U
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FX
Cat. No.
VCGT 110301R-FX
6.35 3.18
0.1
110301L-FX 0.1
110302R-FX 0.2
110302L-FX 0.2
110304R-FX 0.4
110304L-FX 0.4
VCET Grades Dimensions (mm)
ACZ150
Inscribed circle
Thickness
Nose radius
FY
Cat. No.
VCET 1103008R-FY
6.35 3.18
0.08
1103008L-FY 0.08
110301R-FY 0.1
110301L-FY 0.1
1103018R-FY 0.18
1103018L-FY 0.18
VCGT Grades Dimensions (mm)
AC520U
AC1030U
AC530U
Inscribed circle
Thickness
Nose radius
FY
Cat. No.
VCGT 110301R-FY
6.35 3.18
0.1
110301L-FY 0.1
110302R-FY 0.2
110302L-FY 0.2
110304R-FY 0.4
110304L-FY 0.4
7 Positive G Class
VCGT Grades Dimensions (mm)
AC520U
AC1030U
AC530U
ACZ150
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FC
Cat. No.
VCGT 080204MN-FC 4.76 2.38 0.4
VCGT 110301MN-FC
6.35 3.18
0.1
110302MN-FC 0.2
110304MN-FC 0.4
Nose radii with a sign "<" indicate negative tolerances.
VCMT
Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC830P
AC610M
AC630M
AC6020M
AC6030M
AC6040M
AC520U
AC530U
Inscribed circle
Thickness
Nose radius
SU
Cat. No.
VCMT 080204N-SU 4.76 2.38 0.4
VCMT 110302N-SU
6.35 3.18
0.2
110304N-SU 0.4
110308N-SU 0.8
VCMT 160404N-SU 9.525 4.76 0.4
160408N-SU 0.8
SEC-Boring Bars
SVJC Type / SVQC Type / SVUC Type / SVZC Type
VCMT Grades Dimensions (mm)
AC820P
AC8025P
AC830P
AC6020M
AC6030M
AC6040M
T1500Z
T3000Z
T1500A
Inscribed circle
Thickness
Nose radius
LB
Cat. No.
VCMT 080202N-LB 4.76 2.38 0.2
080204N-LB 0.4
VCMT 160404N-LB 9.525 4.76 0.4
160408N-LB 0.8
7 Positive G Class
VCGT Grades Dimensions (mm)
AC610M
AC630M
AC510U
AC520U
AC1030U
AC530U
T1500Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
SI
Cat. No.
VCGT 110301MN-SI
6.35 3.18
0.1
110302MN-SI 0.2
110304MN-SI 0.4
110308MN-SI 0.8
VCGT 160401MN-SI
9.525 4.76
0.1
160402MN-SI 0.2
160404MN-SI 0.4
160408MN-SI 0.8
Nose radii with a sign "<" indicate negative tolerances.
Boring
Bars
E48
E
SEC-Boring Bars
SVJC Type / SVQC Type / SVUC Type / SVZC Type
7 Positive M Class
SUMIBORON One Use Inserts (Non-Coated)
NU-
VCGW
Grades Dimensions (mm)
BN1000
BN2000
BN7000
BN700
Inscribed circle
Thickness
Nose radius
Cat. No.
NU-VCGW 080202
4.76 2.38
0.2
080204 0.4
080208 0.8
080202LT 0.2
080204LT 0.4
080208LT 0.8
080202HS 0.2
080208HS 0.8
NU-VCGW 110302
6.35 3.18
0.2
110304 0.4
110302HS 0.2
110304HS 0.4
NU-VCGW 160404 6.35 3.18 0.4
Note: The part number suffixes stand for the following: LT: Cutting performance focused type LS: Continuous cut general-purpose type HS: Strengthened cutting edge type
7 Positive M Class
SUMIBORON
VCMW
Grades Dimensions (mm)
BNX20
BN500
Inscribed circle
Thickness
Nose radius
Cat. No.
VCMW 160404 9.525 4.76 0.4
160408 0.8
7 Positive M Class
SUMIDIA NF Inserts
NF-
VCMT
Grades Dimensions (mm)
DA1000
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
NF-VCMT 110304
6.35 3.18
0.4
110308 0.8
110312 1. 2
NF-VCMT 160404
9.525 4.76
0.4
160408 0.8
160412 1. 2
VCMT Grades Dimensions (mm)
DA1000
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
VCMT 110301
6.35 3.18
0.1
110302 0.2
110304 0.4
VCMT 160408
9.525 4.76
0.8
160412 1. 2
160412-WF 1. 2
Note: The part number suffixes stand for the following: WF: Cutting edge with special land for aluminum wheel gloss finishing
VCMW Grades Dimensions (mm)
NPD10
Inscribed circle
Thickness
Nose radius
RH
Cat. No.
VCMW 080201RH
4.76 2.38
0.1
080202RH 0.2
080204RH 0.4
VCMW 110302RH 6.35 3.18 0.2
110304RH 0.4
VCMW 160402RH
9.525 4.76
0.2
160404RH 0.4
160408RH 0.8
160412RH 1. 2
NF-
VCMT
Grades Dimensions (mm)
DA1000
Inscribed circle
Thickness
Nose radius
LD/GD
Cat. No.
NF-VCMT 110302N-LD
6.35 3.18
0.2
110304N-LD 0.4
110302N-GD 0.2
110304N-GD 0.4
NF-VCMT 160404N-LD
9.525 4.76
0.4
160408N-LD 0.8
160412N-LD 1. 2
160404N-GD 0.4
160408N-GD 0.8
160412N-GD 1. 2
Note: The part number suffixes stand for the following: LD: For finishing GD: For medium finishing
7 Positive G Class
SUMIBORON Multi Corner One Use Inserts (Coated)
2NC-
VCGW
Grades Dimensions (mm)
BNC2010
BNC2020
BNC100
BNC160
BNC200
Inscribed circle
Thickness
Nose radius
Cat. No.
2NC-VCGW 080202 4.76 2.38 0.2
080204 0.4
2NC-VCGW 160404
9.525 4.76
0.4
160408 0.8
160404LS 0.4
160408LS 0.8
160404HS 0.4
160408HS 0.8
Note: The part number suffixes stand for the following: HS: Strengthened cutting edge type
Inserts ( SUMIBORON / SUMIDIA)
mark: To be replaced by new item (Please confirm stock availability)
Boring
Bars
E49
E
SEC-Boring Bars
S-SSKP Type / C-SSKP Type
Parts
Holders
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head Rake
angle
Applicable inserts Screw Wrench
RL
DMIN
DCON
HLFWFLH
GAMF
Steel
S12M-SSKP R/L0903-16
BBPS-312 R/L 16 12 11 150 8.0 9.0 6
SP 0903
BFTX0307A
2.0 TRX10
S16R-SSKP R/L0903-20
BBPS-316 R/L 20 16 15 200 10.0 6.8 4
S20S-SSKP R/L0903-25
BBPS-320 R/L 25 20 18 250 12.5 8.5 2
S25T-SSKP R/L0903-28
BBPS-325 R/L 28 25 22 300 14.0 5.0 0
General Boring
Parts
Holders
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle
Applicable inserts Screw Wrench
R
DMIN
DCON
HLFWFLH
GAMF
Carbide Standard
C12M-SSKP R0903-16
WBPS-312 R S
16 12 11 150 8 25 6
SP 0903
BFTX0307A
2.0 TRX10
Carbide
Long
C12R-SSKP R0903-16
WBPS-312 R
16 12 11 200 8 25 6
C16S-SSKP R0903-20
WBPS-316 R
20 16 15 250 10 30 4
11 Positive G Class
SPGT Grades Dimensions (mm)
T1500Z
T3000Z
T1000A
T1500A
ST10P
G10E
Inscribed circle
Thickness
Nose radius
SD
Cat. No.
SPGT 090302R-SD
9.525 3.18
0.2
090302L-SD 0.2
090304R-SD 0.4
090304L-SD 0.4
090308R-SD 0.8
090308L-SD 0.8
SPGW Grades Dimensions (mm)
G10E
Inscribed circle
Thickness
Nose radius
Cat. No.
SPGW 090304 9.525 3.18 0.4
11 Positive M Class
SPMT Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC630M
AC6030M
AC6040M
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
LU
Cat. No.
SPMT 090304N-LU 9.525 3.18 0.4
090308N-LU 0.8
SPMT Grades Dimensions (mm)
AC820P
AC8025P
AC830P
AC6020M
AC6030M
AC6040M
T1500Z
T3000Z
T1500A
Inscribed circle
Thickness
Nose radius
LB
Cat. No.
SPMT 090304N-LB 9.525 3.18 0.4
090308N-LB 0.8
11 Positive M Class
SPMT Grades Dimensions (mm)
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FB
Cat. No.
SPMT 090304N-FB 9.525 3.18 0.4
090308N-FB 0.8
SPMT Grades Dimensions (mm)
AC820P
AC8025P
AC830P
Inscribed circle
Thickness
Nose radius
SF
Cat. No.
SPMT 090304N-SF 9.525 3.18 0.4
090308N-SF 0.8
Inserts (Coated carbide / Cermet / Carbide)
Through Boring
S-SSKP
Steel
75°
5°
DCON
GAMF LF
LH
WF
H
DMIN Min.
machinable diameter
Through Boring
C-SSKP
Carbide
Carbide
Long
75°
5°
DCON
GAMF LF
LH
WF
H
DMIN Min.
machinable diameter
75°
(For Torx holes)
(For Torx holes)
Recommended tightning torque (N m) mark: To be replaced by new item (Please confirm stock availability)
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
Boring
Bars
E50
E
SEC-Boring Bars
S-CSKP Type
mark: To be replaced by new item (Please confirm stock availability)
General Boring (Top Clamp Type)
Parts
Holders
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle
Applicable inserts Clamp
Double ended
screws
Wrench
RL
DMIN
DCON
HLFWFLH
GAMF
Steel
S16Q-CSKP R/L0903-20
S16Q-CSKP R/L09
20 16 15 180 10.0 28 4SP 0903
CCM6B L/R
WB6-10 LH030
S20R-CSKP R/L0903-25
S20R-CSKP R/L09
25 20 18 200 12.5 28 2WB6-13
Inserts (Coated carbide / Cermet / Carbide)
11 Positive G Class
SPGR Grades Dimensions (mm)
ST10P
Inscribed circle
Thickness
Nose radius
W
Cat. No.
SPGR 090304L-W 9.525 3.18 0.4
SPGN Grades Dimensions (mm)
AC510U
T1000A
T1500A
T110A
T1200A
G10E
H1
NB90S
Inscribed circle
Thickness
Nose radius
Cat. No.
SPGN 090304 9.525 3.18 0.4
090308 0.8
S-CSKP
Through Boring
Steel
75°
5°
DCON
GAMF LF
LH
WF
H
DMIN Min.
machinable diameter
75°
This figure shows right handed tools.
Dimensions (mm)
You may also use the inserts with holes on page E49.
11 Positive M Class
SPMR Grades Dimensions (mm)
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FK
Cat. No.
SPMR 090304N-FK 9.525 3.18 0.4
090308N-FK 0.8
SPMR Grades Dimensions (mm)
AC820P
AC8025P
AC830P
Inscribed circle
Thickness
Nose radius
SF
Cat. No.
SPMR 090304N-SF 9.525 3.18 0.4
090308N-SF 0.8
SPMR Grades Dimensions (mm)
AC820P
AC8025P
AC830P
Inscribed circle
Thickness
Nose radius
UJ
Cat. No.
SPMR 090304N-UJ 9.525 3.18 0.4
090308N-UJ 0.8
SPMN Grades Dimensions (mm)
AC405K
AC415K
AC420K
T1000A
T1500A
T1200A
ST20E
A30
Inscribed circle
Thickness
Nose radius
Cat. No.
SPMN 090304 9.525 3.18 0.4
090308 0.8
Boring
Bars
E51
E
mark: To be replaced by new item (Please confirm stock availability)
SEC-Boring Bars
CSKP Type
11 Positive G Class
SUMIDIA NF Inserts
NF-
SPGN
Grades Dimensions (mm)
DA1000
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
NF-SPGN 090304 9.525 3.18 0.4
090308 0.8
SUMIDIA
SPGN Grades Dimensions (mm)
DA150
Inscribed circle
Thickness
Nose radius
Cat. No.
SPGN 090304 9.525 3.18 0.4
090308 0.8
11 Positive M Class
SUMIBORON One Use Inserts (Non-Coated)
(DF mark: Only packages containing one piece are in stock, AK mark: Packages containing one piece and
packages containing 10 pieces are in stock)
NU-
SPGN
Grades Dimensions (mm)
BNX20
BN2000
BN500
BN7000
BN700
Inscribed circle
Thickness
Nose radius
Cat. No.
NU-SPGN 090304
9.525 3.18
0.4
090308 0.8
090304LT 0.4
090308LT 0.8
090304HS 0.4
090308HS 0.8
Note: The part number suffixes stand for the following: LT: Cutting performance focused type HS: Strengthened cutting edge type
SUMIBORON
SPGN Grades Dimensions (mm)
BNX20
BN7000
BN700
Inscribed circle
Thickness
Nose radius
Cat. No.
SPGN 090304 9.525 3.18 0.4
090308 0.8
You may also use the inserts with holes on page E49.
Boring
Bars
E52
E
General Boring
Parts
Holders
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle
Applicable inserts Screws Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Steel
S16R-SSKC R/L09T3-20
S16R-SSKC R/L09
20 16 15 200 11 23
10
SC 09T3
BFTX0407N
3.4 TRX15
S20S-SSKC R/L09T3-25
S20S-SSKC R/L09
25 20 18 250 13 27
8
BFTX0409N
3.4
S25T-SSKC R/L1204-32
S25T-SSKC R/L12
32 25 23 300 17 30
7
SC 1204
BFTX0511N
5.0 TRX20
S32U-SSKC R/L1204-40
S32U-SSKC R/L12
40 32 30 350 22 33
6
Inserts (Coated carbide / Cermet / SUMIDIA)
7 Positive G Class
SCGT Grades Dimensions (mm)
AC1030U
AC530U
Inscribed circle
Thickness
Nose radius
FX
Cat. No.
SCGT 09T302R-FX
9.525 3.97
0.2
09T302L-FX 0.2
09T304R-FX 0.4
09T304L-FX 0.4
SCGT 120404R-FX 12.70 4.76 0.4
120404L-FX 0.4
SCGT Grades Dimensions (mm)
AC1030U
AC530U
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
SC
Cat. No.
SCGT 09T301MN-SC 9.525 3.97 0.1
09T302MN-SC 0.2
Nose radii with a sign "<" indicate negative tolerances.
SCMT
Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC630M
AC6030M
AC6040M
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
LU
Cat. No.
SCMT 09T304N-LU 9.525 3.97 0.4
09T308N-LU 0.8
SCMT Grades Dimensions (mm)
T1500A
Inscribed circle
Thickness
Nose radius
FP
Cat. No.
SCMT 09T304N-FP 9.525 3.97 0.4
09T308N-FP 0.8
SCMT 120404N-FP 12.70 4.76 0.4
120408N-FP 0.8
7 Positive M Class
SCMT Grades Dimensions (mm)
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FB
Cat. No.
SCMT 09T304N-FB 9.525 3.97 0.4
09T308N-FB 0.8
SCMT Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC830P
AC610M
AC630M
AC6020M
AC6030M
AC6040M
Inscribed circle
Thickness
Nose radius
SU
Cat. No.
SCMT 09T304N-SU 9.525 3.97 0.4
09T308N-SU 0.8
SCMT 120404N-SU 12.7 4.76 0.4
120408N-SU 0.8
SCMT Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC630M
AC6020M
AC6030M
AC405K
AC415K
AC420K
Inscribed circle
Thickness
Nose radius
MU
Cat. No.
SCMT 09T308N-MU 9.525 3.97 0.8
SCMT 120408N-MU 12.7 4.76 0.8
7 Positive M Class
SCMT Grades Dimensions (mm)
AC820P
AC8025P
AC830P
AC6020M
AC6030M
AC6040M
T1500Z
T3000Z
T1500A
Inscribed circle
Thickness
Nose radius
LB
Cat. No.
SCMT 09T304N-LB 9.525 3.97 0.4
09T308N-LB 0.8
SCMW
Grades Dimensions (mm)
AC405K
AC415K
AC420K
Inscribed circle
Thickness
Nose radius
Cat. No.
SCMW 09T308 9.525 3.97 0.8
SCMW 120408 12.7 4.76 0.8
120412 1. 2
SUMIDIA
SCMT Grades Dimensions (mm)
DA150
Inscribed circle
Thickness
Nose radius
Cat. No.
SCMT 09T301
9.525 3.97
0.1
09T302 0.2
09T304 0.4
Through Boring
S-SSKC
Steel
75°
0°
DCON
GAMF
LF
LH
WF
H
DMIN Min.
machinable diameter
SEC-Boring Bars
S-SSKC Type 75°
(For Torx holes)
Recommended tightning torque (N m) mark: To be replaced by new item (Please confirm stock availability)
This figure shows right handed tools.
Dimensions (mm)
Boring
Bars
E53
E
Recommended tightning torque(N m) mark: Standard stocked item (expanded product)
SEC-Boring Bars
S-DSKN Type / S-PSKN Type
General Boring
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Conventional
Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head Fig Applicable inserts Lever
pins Bolts Shims
Shim
retainers
Wrenches
RL
DMIN
DCON
HLFWFLH Cat. No.
Page
Steel
S32S-PSKN R/L1204-40
40 32 30 250 22.0 (21)
1
SN 1204
LCL4 LCS4
LSS42B
LSP4 LH030
S32S-PSKN R/L1204-44
S32S-PSKN R/L12
44 32 30 250 22.0 (21)
From
B41
S40T-PSKN R/L1204-50
50 40 37 300 27.0 (21)
S40T-PSKN R/L1204-54
S40T-PSKN R/L12
54 40 37 300 27.0 (21)
LSS42
S50U-PSKN R/L1204-63
63 50 47 350 31.5 2
LSS42B
S50U-PSKN R/L1906-70
S50U-PSKN R/L19
70 50 47 350 35.0 (31) 1
SN 1906
From
B47
LCL6 LCS6
LSS63
LSP6 LH040
The values in ( ) are reference values.
S-PSKN
Through Boring
Steel
Fig 1
DMIN Min.
machinable diameter
75°
-6°
-10°
LH
DCON
LF
WF
H
Inserts
SNMG120408N-GE
SNMG190608N-UX
(Representative
example)
GE type UX type
Through Boring
S-DSKN
Steel
Fig 1 Fig 2
LH
75°
-6°
DCON
GAMF
LF
WF
H
DMIN Min.
machinable diameter
75°
-6°
DCON
GAMF
LF
WF
H
DMIN Min.
machinable diameter
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head Rake
angle
Fig Applicable inserts
Clamp set
Shim Screw
for shim
Wrench for
upper surface
Wrench for
lower surface
RL
DMIN
DCON
HLFWFLH
GAMF
Cat. No.
Page
Steel
S25R-DSKN R/L1204-32
32 25 23 200 17.0 (26)
13
1
SN 1204
From
B41
SCP-2 5.0
SNS1203B
BFTX0307N
LH040 LH025
S32S-DSKN R/L1204-40
40 32 30 250 22.0 (21)
10
S40T-DSKN R/L1204-50
50 40 37 300 27.0 (21)
10
S50U-DSKN R/L1204-63
63 50 47 350 31.5
10
2
The values in ( ) are reference values.
Parts for clamp set
E81
75°
Fig 2
75°
f
Fig 3
75°
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
Boring
Bars
E54
E
SEC-Boring Bars
S-ESKN Type / S-PSYN Type / S-ESYN Type
General Boring
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head Rake
angle
Applicable inserts Shim Eccentric
shaft Wrench
RL
DMIN
DCON
HLFWFLH
GAMF
Cat. No.
Page
Steel
S25R-ESYN R/L1204-34
BSYN425 R/L 34 25 23 200 17 (20)
12
SN 1204
From
B41
SSW423 CPB42 LH030
S32S-ESYN R/L1204-44
BSYN432 R/L 44 32 30 250 22 (22)
10
CPB43S
The values in ( ) are reference values.
S-ESYN
Through Boring
Steel
85°
– 6°
( )
LH
DCON
GAMF
LF
WF
H
DMIN Min.
machinable diameter
Inserts
SNMG120408N-GE
(Representative
example)
85°
75°
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Applicable inserts Lever
pin Bolt Shim Shim
retainer Wrench
RL
DMIN
DCON
HLFWFLHCat. No. Page
Steel
S32S-PSYN R/L1204-44
S32S-PSYN R/L12
44 32 30 250 22 (22)
SN 1204
From
B41
LCL4 LCS4
LSS42B
LSP4 LH030
The values in ( ) are reference values.
S-PSYN
Through Boring
Steel
– 6°
– 10°
85°
( )
LH
DCON
LF
WF
H
DMIN Min.
machinable diameter
Inserts
SNMG120408N-GE
(Representative
example)
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle
Applicable inserts Shims Eccentric
shafts Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Cat. No. Page
Steel
S25R-ESKN R/L1204-34
BSKN425 R/L 34 25 23 200 17 (18)
12
SN 1204
From
B41
SSW423
CPB42
LH030
S32S-ESKN R/L1204-44
BSKN432 R/L 44 32 30 250 22 (20)
10
CPB43S
S40T-ESKN R/L1204-54
BSKN440 R/L 54 40 37 300 27 (20)
10
CPB43
S50U-ESKN R/L1906-70
BSKN650 R/L 70 50 47 350 35 (30)
10
SN 1906
From
B47
SSW635 CPB64 LH040
The values in ( ) are reference values.
Inserts
SNMG120408N-GE
SNMG190612N-UX
(Representative
example)
UX type
S-ESKN
Through Boring
Steel
75°
– 6°
( )
LH
DCON
GAMF
LF
WF
H
DMIN Min.
machinable diameter
GE type
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
Dimensions (mm)
This figure shows right handed tools.
This figure shows right handed tools.
Boring
Bars
E55
E
SEC-Boring Bars
S-SWUB Type / C-SWUB Type
93˚
This figure shows right handed tools.
Dimensions (mm)
This figure shows right handed tools.
Dimensions (mm)
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head Rake
angle
Fig Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Steel
S05H-SWUB R/L0601-06K BBPW-508 RK/LK
5.5 5 4.7 100
2.75
12
1
WB 0601
BFTX0203N
0.5 TRX06
S08H-SWUB R/L0601-06 BBPW-508 R/L
5.5 8 7.0 100
2.75
18
12
2
S08H-SWUB R/L0601-08 BBPW-508 R/L08
8.0 8 7.0 100
4
30
10
S08H-SWUB R/L0802-10 BBPW-608 R/L
10.0 8 7.0 100
5
18
13
2
WB 0802
BFTX02205N
0.5 TRX06
S10K-SWUB R/L0802-12 BBPW-610 R/L
12.0 10 9.0 125
6
20
10
Small Hole Finishing
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Fig Applicable inserts Screw Wrench
RL
DMIN
DCON
HLFWFLH
Carbide C05H-SWUB R/L0601-06K WBPW-508 RK/LK
5.5 5 4.7 100 2.75 1
WB 0601
BFTX0203N
0.5 TRX06
C08K-SWUB R/L0601-06 WBPW-508 R/L
5.5 8 7.0 125 2.75 30 2
C05H-SWUB R/L0601-06K requires a separately sold sleeve, HBB516.
An asterisk (*) indicates that the ISO type code is given on the actual product.
ø16 ø5.0
15 100
Sleeve Stock
HBB 516
Sleeve is sold separately.
S05H-SWUB R/L0601-06K requires a separately sold sleeve, HBB516.
An asterisk (*) indicates that the ISO type code is given on the actual product.
ø16 ø5.0
15 100
Sleeve Stock
HBB 516
Sleeve is sold separately.
S-SWUB
Through Boring
Steel
0°
Fig 2
93° 93°
0°
DCON
GAMF GAMF
LF LF
LH
WF
WF
HH
DMIN Min.
machinable diameter
DCON
DMIN Min.
machinable diameter
Fig 1
C-SWUB
Through Boring
Carbide
0°
93°
Fig 1 Fig 2
93°
0°
DCON
GAMF
LF LF
LH
WF
WF
HH
DMIN Min.
machinable diameter
DCON
DMIN Min.
machinable diameter
–
12°
(For Torx holes)
(For Torx holes)
Recommended tightening torque (N·m)
Boring
Bars
E56
E
SEC-Boring Bars
SWUB Type
Inserts (Coated carbide / Cermet / SUMIBORON / SUMIDIA)
5 Positive G Class
WBGT Grades Dimensions (mm)
T1500Z
T1500A
Inscribed circle
Thickness
Nose radius
FW
Cat. No.
WBGT 060102R-FW
3.97 1.59
0.2
060102L-FW 0.2
060104R-FW 0.4
060104L-FW 0.4
WBGT 080202R-FW
4.76 2.38
0.2
080202L-FW 0.2
080204R-FW 0.4
080204L-FW 0.4
WBGT Grades Dimensions (mm)
AC510U
AC1030U
AC530U
Inscribed circle
Thickness
Nose radius
FX
Cat. No.
WBGT 060102R-FX
3.97 1.59
0.2
060102L-FX 0.2
060104R-FX 0.4
060104L-FX 0.4
WBGT 080202R-FX
4.76 2.38
0.2
080202L-FX 0.2
080204R-FX 0.4
080204L-FX 0.4
5 Positive E Class
SUMIBORON One Use Inserts
NU-
WBEW
Grades Dimensions (mm)
BNX20
BN7000
BN700
Inscribed circle
Thickness
Nose radius
Cat. No.
NU-WBEW 060102L-LF
3.97 1.59
0.2
060102L-LT 0.2
060104L-LT 0.4
NU-WBEW 080202L-LT 4.76 2.38 0.2
080204L-LT 0.4
Note: The part number suffixes stand for the following: LF: Sharp edge type LT: Cutting performance focused type
SUMIDIA
WBMT
Grades Dimensions (mm)
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
WBMT 060101L
3.97 1.59
0.1
060102L 0.2
060104L 0.4
5 Positive M Class
SUMIDIA NF Inserts
NF-
WBMT
Grades Dimensions (mm)
DA1000
Inscribed circle
Thickness
Nose radius
Cat. No.
NF-WBMT 060101L
3.97 1.59
0.1
060102L 0.2
060104L 0.4
mark: To be replaced by new item (Please confirm stock availability)
FY type breakers and SUMIBORON and SUMIDIA inserts may also be used for blind hole boring.
WBGT Grades Dimensions (mm)
AC1030U
AC530U
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FY
Cat. No.
WBGT 0601003L-FY
3.97 1.59
0.03
060101R-FY 0.1
060101L-FY 0.1
060102R-FY 0.2
060102L-FY 0.2
060104R-FY 0.4
060104L-FY 0.4
WBGT 080201R-FY
4.76 2.38
0.1
080201L-FY 0.1
080202R-FY 0.2
080202L-FY 0.2
080204R-FY 0.4
080204L-FY 0.4
WBGT Grades Dimensions (mm)
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
W
Cat. No.
WBGT 060102R-W
3.97 1.59
0.2
060102L-W 0.2
060104R-W 0.4
060104L-W 0.4
Boring
Bars
E57
E
SEC-Boring Bars
S-SWUP Type
93˚
Recommended tightning torque(N m) mark: Standard stocked item (expanded product)
Dimensions (mm)
Small Hole Finishing
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle
Applicable inserts Screws Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Steel
S12M-SWUP R/L1102-14 14 12 11 150 7 17 6WP 1102 BFTX02505N 1. 1 TRX08
S16Q-SWUP R/L1102-18 18 16 15 180 9 18 3
S16Q-SWUP R/L1603-18 18 16 15 180 9 18 3WP 1603 BFTX0407N 3.4 TRX15
S20R-SWUP R/L1603-22 22 20 18 200 11 18 2
S-SWUP
Through Boring
Steel
93°
5°
DCON
GAMF LF
LH
WF
H
DMIN Min.
machinable diameter
(For Torx holes)
Inserts (Coated carbide / Cermet)
11 Positive M Class
WPMT Grades Dimensions (mm)
AC820P
AC830P
AC6030M
AC6040M
T1500Z
T3000Z
T1500A
Inscribed circle
Thickness
Nose radius
LB
Cat. No.
WPMT 110204N-LB 6.35 2.38 0.4
WPMT 160308N-LB 9.525 3.18 0.8
This figure shows right handed tools.
Boring
Bars
E58
E
SEC-Boring Bars
S-STUB Type / S-STUP Type
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle
Fig Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLF
WF LH
GAMF
Steel
S08H-STUB R/L0601-08
BBPT-508 R/L 8 8 7
100
4.0
30
12
1TB 0601
BFTX0204A
0.5 TRX06
S08H-STUP R/L0802-10
BBPT-608 R/L 10 8 7
100
5.0
13
10
1TP 0802
S08H-STUP R/L0902-10
10 8 7
100
5.0
13
10
2TP 0902
BFTX02505N
1. 1 TRX08
S10K-STUP R/L1103-12
BBPT-210 R/L 12 10 9
125
6.0
15
8
2TP 110 3
BFTX0306A
2.0
TRX10
S12M-STUP R/L1103-14
BBPT-212 R/L14 14 12 11
150
7. 0
17
7
S12M-STUP R/L1103-16
BBPT-212 R/L 16 12 11
150
8.0
17
6
BFTX0307A
2.0
S16R-STUP R/L1103-18
BBPT-216 R/L18 18 16 15
200
9.0
18
4
BFTX0306A
2.0
S16R-STUP R/L1103-20
BBPT-216 R/L 20 16 15
200
10.0
18
2
BFTX0307A
2.0
S20S-STUP R/L1103-22
BBPT-220 R/L 22 20 18
250
11. 0
18
2
S25T-STUP R/L1103-28
BBPT-225 R/L 28 25 22
300
14.0
27
2
S20S-STUP R/L1603-22
22 20 18
250
11. 0
18
3
2TP 1603
BFTX0407A
3.4 TRX15
S25T-STUP R/L1603-28
28 25 22
300
14.0
18
1
S20S-STUP R/L1604-22
22 20 18
250
12.5
18
5
2TP 1604
BFTX0409N
3.4 TRX15
S20S-STUP R/L1604-25
BBPT-320 R/L 25 20 18
250
12.5
18
3
BFTX0410A
S25T-STUP R/L1604-28
BBPT-325 R/L 28 25 22
300
14.0
18
2
Finish-Medium Cut
Stop Boring
S-STUB
S-STUP
Steel
93°
5°
DMIN Min.
machinable diameter
Fig 1 Fig 2
93°
0°
GAMF GAMF
LH
LH
HH
LF LF
WF
WF
DCON DCON
DMIN Min.
machinable diameter
93˚
(For Torx holes)
Recommended tightning torque (N m) mark: To be replaced by new item (Please confirm stock availability)
Stop Boring
A-STUP
Steel
Oil hole
GAMF
93°
5°
LF
H
DCON
LH
WF
DMIN Min.
machinable diameter
With oil hole
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
(For Torx holes)
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head Rake
angle
Applicable inserts Screws Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Steel with oil hole
A08H-STUP R/L0802-10 10 87100513
10
TP 0802
BFTX0204N
0.5 TRX06
A08H-STUP R/L0902-10 10 87100513
10
TP 0902
BFTX02505N
1. 1 TRX08
A10K-STUP R/L1102-12 12 10 9 125 6 15
8
TP 110 2
BFTX02505N
1. 1
TRX10
A12M-STUP R/L1102-14 14 12 11 150 7 17
7
BFTX02506N
1. 5
A16R-STUP R/L1102-18 18 16 15 200 9 18
4
A10K-STUP R/L1103-12 12 10 9 125 6 15
8
TP 110 3
BFTX0306N
2.0
TRX10
A12M-STUP R/L1103-14 14 12 11 150 7 17
7
A16R-STUP R/L1103-18 18 16 15 200 9 18
4
A20S-STUP R/L1103-22 22 20 18 250 11 18
2
BFTX0307N
2.0
A25T-STUP R/L1103-28 28 25 22 300 14 18
2
A20S-STUP R/L1603-22 22 20 18 250 11 18
3
TP 1603
BFTX0407N
2.0 TRX15
A25T-STUP R/L1603-28 28 25 22 300 14 18
1
A20S-STUP R/L1604-22 22 20 18 250 11 18
5
TP 1604
BFTX0409N
3.4 TRX15
A25T-STUP R/L1604-28 28 25 22 300 14 18
2
BFTX0410N
3.4
This figure shows right handed tools.
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
Boring
Bars
E59
E
SEC-Boring Bars
B-STUP Type / D-STUP Type
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle
Fig Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLF
WF LH
GAMF
Steel with vibration control mechanism
B08H-STUP R/L0802-10
XBPT-608 R/L 10 8 7
100
5.0
13
10
1TP 0802
BFTX0204A
0.5 TRX06
B10K-STUP R/L1103-12
XBPT-210 R/L 12 10 9
125
6.0
15
8
1TP 110 3
BFTX0306A
2.0
TRX10
B12M-STUP R/L1103-14
XBPT-212 R/L14 14 12 11
150
7. 0
17
7
B12M-STUP R/L1103-16
XBPT-212 R/L 16 12 11
150
8.0
17
6
BFTX0307A
2.0
B16R-STUP R/L1103-18
XBPT-216 R/L18 18 16 15
200
9.0
18
4
BFTX0306A
2.0
B16R-STUP R/L1103-20
XBPT-216 R/L 20 16 15
200
10.0
18
2
BFTX0307A
2.0
B20S-STUP R/L1103-22
XBPT-220 R/L 22 20 18
250
11. 0
18
2
B25T-STUP R/L1103-28
XBPT-225 R/L 28 25 22
300
14.0
18
2
B32T-STUP R/L1103-40
XBPT-232 R/L 40 32 30
300
20.0
50
2
2
B20S-STUP R/L1604-25
XBPT-320 R/L 25 20 18
250
12.5
18
3
1TP 1604
BFTX0410A
3.4 TRX15
B25T-STUP R/L1604-28
XBPT-325 R/L 28 25 22
300
14.0
18
2
B32T-STUP R/L1604-40
XBPT-332 R/L 40 32 30
300
20.0
53
2
2
B-STUP
Stop Boring
Steel with
vibration
control
mechanism
93°
5°
DMIN Min.
machinable diameter
Fig 1
93°
5°
DMIN Min.
machinable diameter
Fig 2
GAMF GAMF
LH LH
HH
LF LF
WF
WF
DCON DCON
(For Torx holes)
Finish-Medium Cut
93˚
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle
Applicable inserts Screws Wrench
RL
DMIN
DCON
HLF
WF LH
GAMF
Anti-vibration
with oil hole
D12M-STUP R/L1103-14 XBPT-212 R/L H14
14 12 11
150
717 7
TP 110 3
BFTX0306A
2.0 TRX10
D16R-STUP R/L1103-18 XBPT-216 R/L H18
18 16 15
200
918 4
D20S-STUP R/L1103-22 XBPT-220 R/L H22
22 20 18
250
11 18 2
BFTX0307A
2.0
D-STUP
Stop Boring Oil hole
Steel with
vibration
control
mechanism
93°
5°
DMIN Min.
machinable diameter
GAMF
LH
H
LF
WF
DCON
With oil hole
(For Torx holes)
Recommended tightening torque (N·m)
This figure shows right handed tools.
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
Boring
Bars
E60
E
Finish-Medium Cut
SEC-Boring Bars
C-STUB Type / C-STUP Type / E-STUP Type
93˚
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle
Applicable inserts Screws
Wrenches
R
DMIN
DCON
HLF
WF
LH
GAMF
Carbide
with oil hole
E08H-STUP R0802-10 WBPT-608 RH 10 8
7. 5
100
518
10
TP 0802
BFTX0204A
0.5 TRX06
E10K-STUP R1103-12 WBPT-210 RH 12 10
9.5
125
619
8
TP 110 3
BFTX0306A
2.0
TRX10
E12M-STUP R1103-14 WBPT-212 RH14 14 12
11. 5
150
725
7
E12M-STUP R1103-16 WBPT-212 RH 16 12
11. 5
150
825
6
BFTX0307A
2.0
E16R-STUP R1103-18 WBPT-216 RH18 18 16
15.5
200
930
4
BFTX0306A
2.0
E16R-STUP R1103-20 WBPT-216 RH 20 16
15.5
200
10 30
2
BFTX0307A
2.0
E-STUP
Stop Boring
Carbide
Oil hole 93°
5°
DCON
GAMF
LH
WF
LF
H
DMIN Min.
machinable diameter
With oil hole
(For Torx holes)
Recommended tightening torque (N·m)
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle
Fig Applicable inserts Screws
Wrenches
RL
DMIN
DCON
HLF
WF LH
GAMF
Carbide
Standard
C08H-STUB R/L0601-08
WBPT-508 RS/LS
8 8
7. 0
100
4.0
50
12
1TB 0601
BFTX0204A
0.5 TRX06
C08H-STUB R/L0601-08K
WBPT-508 RSK/LSK
8 6
5.7
100
4.0
12
2
BFTX0204N
0.5
C08H-STUP R/L0802-10
WBPT-608 RS/LS
10 8
7. 0
100
5.0
18
10
3TP 0802
BFTX0204A
0.5 TRX06
C10K-STUP R/L1103-12
WBPT-210 RS/LS
12 10
9.0
125
6.0
19
8
3TP 110 3
BFTX0306A
2.0
TRX10
C12M-STUP R/L1103-14
WBPT-212 RS/LS14
14 12
11. 0
150
7. 0
25
7
C12M-STUP R/L1103-16
WBPT-212 RS/LS
16 12
11. 0
150
8.0
25
6
BFTX0307A
2.0
C16R-STUP R/L1103-18
WBPT-216 RS/LS18
18 16
15.0
200
9.0
30
4
BFTX0306A
2.0
C16R-STUP R/L1103-20
WBPT-216 RS/LS
20 16
15.0
200
10.0
30
2
BFTX0307A
2.0
C20S-STUP R/L1103-22
WBPT-220 RS/LS
22 20
18.0
250
11. 0
35
2
C20S-STUP R/L1604-25
WBPT-320 RS/LS
25 20
18.0
250
12.5
35
3
3TP 1604
BFTX0410A
3.4 TRX15
Carbide
Long
C08M-STUB R/L0601-08
WBPT-508 R/L
8 8
7. 0
150
4.0
50
12
1TB 0601
BFTX0204A
0.5 TRX06
C08M-STUP R/L0802-10
WBPT-608 R/L
10 8
7. 0
150
5.0
18
10
3TP 0802
BFTX0204A
0.5 TRX06
C10Q-STUP R/L1103-12
WBPT-210 R/L
12 10
9.0
180
6.0
19
8
3TP 110 3
BFTX0306A
2.0
TRX10
C12R-STUP R/L1103-14
WBPT-212 R/L14
14 12
11. 0
200
7. 0
25
7
C12R-STUP R/L1103-16
WBPT-212 R/L
16 12
11. 0
200
8.0
25
6
BFTX0307A
2.0
C16S-STUP R/L1103-18
WBPT-216 R/L18
18 16
15.0
250
9.0
30
4
BFTX0306A
2.0
C16S-STUP R/L1103-20
WBPT-216 R/L
20 16
15.0
250
10.0
30
2
BFTX0307A
2.0
Carbide Short
C16M-STUP R/L1103-18
WBPT-216 RE/LE18
18 16
15.0
150
9.0
30
4
3TP 110 3
BFTX0306A
2.0
TRX10
C16M-STUP R/L1103-20
WBPT-216 RE/LE
20 16
15.0
150
10.0
30
2
BFTX0307A
2.0
C20M-STUP R/L1103-22
WBPT-220 RE/LE
22 20
18.0
150
11. 0
35
2
C20M-STUP R/L1604-25
WBPT-320 RE/LE
25 20
18.0
150
12.5
35
3
3TP 1604
BFTX0410A
3.4 TRX15
ø16 ø6.0
15 100
Sleeve Stock
HBB 616
Sleeve is sold separately.
C08H-STUB R/L0601-08K requires a separately sold sleeve, HBB616.
An asterisk (*) indicates that the ISO type code is given on the actual product.
Stop Boring
C-STUB
C-STUP
Carbide
Carbide
Long
Carbide
Short
93°
5°
DCON
Fig 3Fig 2Fig 1
93°
0°
93°
0°
GAMF GAMF GAMF
WF
WF
WF
HHH
LF LF LF
LH
LH
DCON DCON
DMIN Min.
machinable diameter
DMIN Min.
machinable diameter
DMIN Min.
machinable diameter
This figure shows right handed tools.
(For Torx holes)
Dimensions (mm)
Dimensions (mm)
Boring
Bars
E61
E
Inserts ( Coated carbide / Cermet / Carbide)
5 /11 Positive G Class
TBGT
TPGT
Grades Dimensions (mm)
T1500Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FW
Cat. No.
TBGT 060102R-FW
3.97 1.59
0.2
060102L-FW 0.2
060104R-FW 0.4
060104L-FW 0.4
TPGT 080202R-FW
4.76 2.38
0.2
080202L-FW 0.2
080204R-FW 0.4
080204L-FW 0.4
TPGT 110202R-FW
6.35 2.38
0.2
110202L-FW 0.2
110204R-FW 0.4
110204L-FW 0.4
TBGT
TPGT
Grades Dimensions (mm)
AC510U
AC520U
AC1030U
AC530U
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FX
Cat. No.
TBGT 060102R-FX
3.97
1.59
0.2
060102L-FX 0.2
060104R-FX 0.4
060104L-FX 0.4
TPGT 080202R-FX
4.76
2.38
0.2
080202L-FX 0.2
080204R-FX 0.4
080204L-FX 0.4
TPGT 090204L-FX
5.56
2.38 0.4
TPGT 110202R-FX
6.35
2.38
0.2
110202L-FX 0.2
110204R-FX 0.4
110204L-FX 0.4
110208R-FX 0.8
110208L-FX 0.8
TPGT 110302R-FX
6.35
3.18
0.2
110302L-FX 0.2
110304R-FX 0.4
110304L-FX 0.4
110308R-FX 0.8
110308L-FX 0.8
TPGT 160304R-FX
16.5
3.18
0.4
160304L-FX 0.4
160308R-FX 0.8
160308L-FX 0.8
5 /11 Positive G Class
TBGT
TPGT
Grades Dimensions (mm)
AC520U
AC1030U
AC530U
ACZ150
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FY
Cat. No.
TBGT 060101R-FY
3.97 1.59
0.1
060101L-FY 0.1
060102R-FY 0.2
060102L-FY 0.2
060104R-FY 0.4
060104L-FY 0.4
TPGT 0802003R-FY
4.76 2.38
0.03
0802003L-FY 0.03
080201R-FY 0.1
080201L-FY 0.1
080202R-FY 0.2
080202L-FY 0.2
080204R-FY 0.4
080204L-FY 0.4
TPGT 090201R-FY
5.56 2.38
0.1
090201L-FY 0.1
090202R-FY 0.2
090202L-FY 0.2
090204R-FY 0.4
090204L-FY 0.4
TPGT 110202R-FY
6.35 2.38
0.2
110202L-FY 0.2
110204R-FY 0.4
110204L-FY 0.4
110208R-FY 0.8
110208L-FY 0.8
TPGT 1103003R-FY
6.35 3.18
0.03
1103003L-FY 0.03
110301R-FY 0.1
110301L-FY 0.1
110302R-FY 0.2
110302L-FY 0.2
110304R-FY 0.4
110304L-FY 0.4
110308R-FY 0.8
110308L-FY 0.8
TPGT 160302R-FY
16.5 3.18
0.2
160302L-FY 0.2
160304R-FY 0.4
160304L-FY 0.4
160308R-FY 0.8
160308L-FY 0.8
SEC-Boring Bars
STUB Type / STUP Type
TBGT
TPGT
Grades Dimensions (mm)
AC1030U
AC530U
T1500Z
T3000Z
T1000A
T1500A
ST10P
G10E
Inscribed circle
Thickness
Nose radius
W
Cat. No.
TBGT 060102R-W
3.97 1.59
0.2
060102L-W 0.2
060104R-W 0.4
060104L-W 0.4
TPGT 080202R-W
4.76 2.38
0.2
080202L-W 0.2
080204R-W 0.4
080204L-W 0.4
TBGW
TPGW
Grades Dimensions (mm)
AC503U
AC510U
T1000A
T1500A
G10E
Inscribed circle
Thickness
Nose radius
Cat. No.
TBGW 060102 3.97 1.59 0.2
060104 0.4
TPGW 080202 4.76 2.38 0.2
TPGW 110302
6.35 3.18
0.2
110304 0.4
110308 0.8
TPGW 160404 9.525 4.76 0.4
Boring
Bars
E
E62
Inserts ( Coated carbide / Cermet / Carbide)
SEC-Boring Bars
STUB Type / STUP Type
11 Positive G Class
TPGX Grades Dimensions (mm)
T1500Z
T3000Z
T1500A
Inscribed circle
Thickness
Nose radius
SDW
Cat. No.
TPGX 110304R-SDW
6.35 3.18
0.4
110304L-SDW 0.4
110308R-SDW 0.8
110308L-SDW 0.8
TPGX 160404R-SDW
9.525 4.76
0.4
160404L-SDW 0.4
160408R-SDW 0.8
160408L-SDW 0.8
TPGT Grades Dimensions (mm)
AC520U
AC530U
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FC
Cat. No.
TPGT 110302MN-FC 6.35 3.18 0.2
110304MN-FC 0.4
Nose radii with a sign "<" indicate negative tolerances.
TPMT
Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC830P
AC610M
AC630M
AC6020M
AC6030M
AC6040M
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
SU
Cat. No.
TPMT 080202N-SU 4.76 2.38 0.2
080204N-SU 0.4
TPMT 110302N-SU
6.35 3.18
0.2
110304N-SU 0.4
110308N-SU 0.8
TPMT 160404N-SU 9.525 4.76 0.4
160408N-SU 0.8
TPMT Grades Dimensions (mm)
AC820P
AC8025P
AC830P
AC6020M
AC6030M
AC6040M
T1500Z
T3000Z
T1500A
Inscribed circle
Thickness
Nose radius
LB
Cat. No.
TPMT 080202N-LB
4.76
2.38 0.2
080204N-LB 0.4
TPMT 090202N-LB
5.56
2.38 0.2
090204N-LB 0.4
TPMT 110302N-LB
6.35
3.18
0.2
110304N-LB 0.4
110308N-LB 0.8
TPMT 160304N-LB
9.525
3.18 0.4
160308N-LB 0.8
TPMT 160404N-LB
9.525
4.76 0.4
160408N-LB 0.8
TPMT Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC630M
AC6030M
AC6040M
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
LU
Cat. No.
TPMT 080202N-LU 4.76 2.38 0.2
080204N-LU 0.4
TPMT 090202N-LU 5.56 2.38 0.2
090204N-LU 0.4
TPMT 110302N-LU
6.35 3.18
0.2
110304N-LU 0.4
110308N-LU 0.8
TPMT Grades Dimensions (mm)
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FK
Cat. No.
TPMT 110308N-FK 6.35 3.18 0.8
TPMT 160404N-FK 9.525 4.76 0.4
160408N-FK 0.8
11 Positive M Class
TPMT Grades Dimensions (mm)
AC530U
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FB
Cat. No.
TPMT 080202N-FB 4.76 2.38 0.2
080204N-FB 0.4
TPMT 090202N-FB 5.56 2.38 0.2
090204N-FB 0.4
TPMT 110302N-FB
6.35 3.18
0.2
110304N-FB 0.4
110308N-FB 0.8
TPMT 160304N-FB 9.525 3.18 0.4
160308N-FB 0.8
TPMT 160404N-FB 9.525 4.76 0.4
160408N-FB 0.8
5 /11 Positive G Class
TBGT
TPGT
Grades Dimensions (mm)
H1
Inscribed circle
Thickness
Nose radius
AY
Cat. No.
TBGT 060101R-AY
3.97 1.59
0.1
060101L-AY 0.1
060102R-AY 0.2
060102L-AY 0.2
060104R-AY 0.4
060104L-AY 0.4
TPGT 080201R-AY
4.76 2.38
0.1
080201L-AY 0.1
080202R-AY 0.2
080202L-AY 0.2
080204R-AY 0.4
080204L-AY 0.4
TPGT 090201R-AY
5.56 2.38
0.1
090201L-AY 0.1
090202R-AY 0.2
090202L-AY 0.2
090204R-AY 0.4
090204L-AY 0.4
TPGT 110202R-AY
6.35 2.38
0.2
110202L-AY 0.2
110204R-AY 0.4
110204L-AY 0.4
TPGT 110301R-AY
6.35 3.18
0.1
110301L-AY 0.1
110302R-AY 0.2
110302L-AY 0.2
110304R-AY 0.4
110304L-AY 0.4
TPGT Grades Dimensions (mm)
AC510U
AC1030U
AC530U
T1500Z
T3000Z
T2000Z
T1000A
T1500A
ST10P
G10E
Inscribed circle
Thickness
Nose radius
SD
Cat. No.
TPGT 110302R-SD
6.35 3.18
0.2
110302L-SD 0.2
110304R-SD 0.4
110304L-SD 0.4
110308R-SD 0.8
110308L-SD 0.8
TPGT 160402R-SD
9.525 4.76
0.2
160402L-SD 0.2
160404R-SD 0.4
160404L-SD 0.4
160408R-SD 0.8
160408L-SD 0.8
11 Positive G Class
Boring
Bars
E63
E
11 Positive M Class
TPMT Grades Dimensions (mm)
AC810P
AC820P
AC8025P
AC630M
AC6020M
AC6030M
AC405K
AC415K
AC420K
Inscribed circle
Thickness
Nose radius
MU
Cat. No.
TPMT 110304N-MU 6.35 3.18 0.4
110308N-MU 0.8
TPMT 160404N-MU 9.525 4.76 0.4
160408N-MU 0.8
TPMH
TPMT
Grades Dimensions (mm)
AC820P
AC8025P
AC830P
Inscribed circle
Thickness
Nose radius
SF
Cat. No.
TPMH 110304N-SF 6.35 3.18 0.4
110308N-SF 0.8
TPMT 160404N-SF 9.525 4.76 0.4
160408N-SF 0.8
5 / 11 Positive E Class / G Class
SUMIBORON One Use Inserts
( mark: Only packages containing one piece are in stock, mark: Packages containing one piece and
packages containing 10 pieces are in stock)
NU-TBEW
NU-TPGW
Grades Dimensions (mm)
BNX10
BNX20
BNX25
BN1000
BN2000
BN350
BN500
BN7000
BN700
Inscribed circle
Thickness
Nose radius
Cat. No.
NU-TBEW 060102LT 3.97 1.59 0.2
NU-TPGW 080202
4.76 2.38
0.2
080204 0.4
080208 0.8
080204LF 0.4
080202LT 0.2
080204LT 0.4
080202HS 0.2
080204HS 0.4
080208HS 0.8
NU-TPGW 090202
5.56 2.38
0.2
090204 0.4
090208 0.8
090202LT 0.2
090204LT 0.4
090202HS 0.2
090204HS 0.4
NU-TPGW 110202
6.35 2.38
0.2
110204 0.4
110202LT 0.2
110204LT 0.4
110204HS 0.4
NU-TPGW 110302
6.35 3.18
0.2
110304 0.4
110308 0.8
NS-TPGW 110304 0.4
110308 0.8
NU-TPGW 110302LF 0.2
110304LF 0.4
110308LF 0.8
110302LT 0.2
110304LT 0.4
110308LT 0.8
110302HS 0.2
110304HS 0.4
110308HS 0.8
NU-TPGW 160302
9.525 3.18
0.2
160304 0.4
160308 0.8
NU-TPGW 160404
9.525 4.76
0.4
160408 0.8
NS-TPGW 160404 0.4
160408 0.8
NU-TPGW 160404LF 0.4
160404LT 0.4
160408LT 0.8
160404HS 0.4
160408HS 0.8
Note: The part number suffixes stand for the following: LF: Sharp edge LT: Cutting performance focused type HS: Strengthened cutting edge type
Inserts (Coated carbide / Cermet / Carbide / SUMIBORON)
SEC-Boring Bars
STUB Type / STUP Type
Boring
Bars
E64
E
mark: To be replaced by new item (Please confirm stock availability)
Inserts (SUMIBORON)
11 Positive M Class
SUMIBORON Multi Corner One Use Inserts (Coated)
3NC
-
TPGW
Grades Dimensions (mm)
BNC2010
BNC2020
BNC100
BNC160
BNC200
BNC300
BNC500
Inscribed circle
Thickness
Nose radius
Cat. No.
3NC-TPGW 080202 4.76 2.38 0.2
080204 0.4
3NC-TPGW090202 5.56 2.38 0.2
090204 0.4
3NC-TPGW 110302
6.35 3.18
0.2
110304 0.4
110308 0.8
110302LE 0.2
110304LE 0.4
110308LE 0.8
110302LT 0.2
110304LT 0.4
110308LT 0.8
110304LS 0.4
110308LS 0.8
110304HS 0.4
110308HS 0.8
3NC-TPGW 160404
9.525 4.76
0.4
160408 0.8
160404LS 0.4
160408LS 0.8
160404HS 0.4
160408HS 0.8
Note: The part number suffixes stand for the following: LE: Low resistance type LT/LS: Cutting performance focused type HS: Strengthened cutting edge type
SEC-Boring Bars
STUB Type / STUP Type
SUMIBORON Break Master (Coated)
3NC-
TPGT
Grades Dimensions (mm)
BNC2010
BNC2020
BNC160
BNC200
Inscribed
circle
Thickness
Nose radius
Cat. No.
3NC-TPGT 110304N-FV 6.35 3.18 0.4
110308N-FV 0.8
SUMIBORON
TPGW Grades Dimensions (mm)
BNX20
BN2000
BN500
BN7000
BN700
Inscribed circle
Thickness
Nose radius
Cat. No.
TPGW 110304
6.35 3.18
0.4
110308 0.8
110304HS 0.4
110308HS 0.8
TPGW 160404
9.525 4.76
0.4
160408 0.8
160404HS 0.4
160408HS 0.8
Note: The part number suffixes stand for the following: HS: Strengthened cutting edge type
11 Positive M Class
SUMIBORON Multi Corner One Use Inserts (Non-Coated)
3NU
-
TPGW
Grades Dimensions (mm)
BN7000
BN7500
Inscribed circle
Thickness
Nose radius
Cat. No.
3NU-TPGW 110304
6.35 3.18
0.4
110308 0.8
110302LF 0.2
110304LF 0.4
110308LF 0.8
110304LE 0.4
110304LS 0.4
Note: The part number suffixes stand for the following: LF/LE: Sharp edge LS:
Continuous cut general-purpose type
SUMIBORON Break Master (Non-Coated)
3NU-
TPGT
Grades Dimensions (mm)
BN2000
Inscribed circle
Thickness
Nose radius
Cat. No.
3NU-TPGT 110304N-FV 6.35 3.18 0.4
110308N-FV 0.8
Boring
Bars
E65
E
mark: To be replaced by new item (Please confirm stock availability)
SEC-Boring Bars
STUB Type / STUP Type
Inserts ( SUMIDIA)
SUMIDIA 5 / 11 Positive G Cass
SUMIDIA NF Inserts
NF-TBGW
NF-TPGW
Grades Dimensions (mm)
DA1000
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
NF-TBGW 060102 3.97 1.59 0.2
060104 0.4
NF-TPGW 080201
4.76 2.38
0.1
080202 0.2
080204 0.4
NF-TPGW 110201
6.35 2.38
0.1
110202 0.2
110204 0.4
NF-TPGW 110301
6.35 3.18
0.1
110302 0.2
110304 0.4
110308 0.8
NF-TPGW 160401
9.525 4.76
0.1
160402 0.2
160404 0.4
160408 0.8
SUMIDIA 5 / 11 Positive M Class / G Class
SUMIDIA
TBGW
TPGW
Grades Dimensions (mm)
DA150
Inscribed circle
Thickness
Nose radius
Cat. No.
TBGW 060102 3.97 1.59 0.2
060104 0.4
TPGW 080202 4.76 2.38 0.2
080204 0.4
TPGW 110202 6.35 2.38 0.2
110204 0.4
TPGW 110302
6.35 3.18
0.2
110304 0.4
110308 0.8
TPGW 160402
9.525 4.76
0.2
160404 0.4
160408 0.8
SUMIDIA 11 Positive M Class
SUMIDIA NF Inserts
NF-
TPMT
Grades Dimensions (mm)
DA1000
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
NF-TPMT 110301
6.35 3.18
0.1
110302 0.2
110304 0.4
110308 0.8
SUMIDIA Break Master
NU-
TPMT
Grades Dimensions (mm)
DA150
Inscribed circle
Thickness
Nose radius
DM
Cat. No.
NU-TPMT 080202L-DM 4.76 2.38 0.2
080204L-DM 0.4
NU-TPMT 110202L-DM 6.35 2.38 0.2
110204L-DM 0.4
NU-TPMT 110302L-DM 6.35 3.18 0.2
110304L-DM 0.4
NU-TPMT 160402L-DM 9.525 4.76 0.2
160404L-DM 0.4
SUMIDIA Break Master
NF-
TPMT
Grades Dimensions (mm)
DA1000
Inscribed circle
Thickness
Nose radius
LD/GD
Cat. No.
NF-TPMT 080202N-LD
4.76 2.38
0.2
080204N-LD 0.4
080202N-GD 0.2
080204N-GD 0.4
NF-TPMT 090202N-LD
5.56 2.38
0.2
090204N-LD 0.4
090202N-GD 0.2
090204N-GD 0.4
NF-TPMT 110202N-LD
6.35 2.38
0.2
110204N-LD 0.4
110202N-GD 0.2
110204N-GD 0.4
NF-TPMT 110302N-LD
6.35 3.18
0.2
110304N-LD 0.4
110308N-LD 0.8
110302N-GD 0.2
110304N-GD 0.4
110308N-GD 0.8
NF-TPMT 160402N-LD
9.525 4.76
0.2
160404N-LD 0.4
160408N-LD 0.8
160402N-GD 0.2
160404N-GD 0.4
160408N-GD 0.8
Note: The part number suffixes stand for the following: LD: For finishing GD: For medium finishing
SUMIDIA Binderless
TPMW Grades Dimensions (mm)
NPD10
Inscribed circle
Thickness
Nose radius
RH
Cat. No.
TPMW 080202RH 4.76 2.38 0.2
080204RH 0.4
TPMW 110302RH
6.35 3.18
0.2
110304RH 0.4
110308RH 0.8
TPMW 160402RH
9.525 4.76
0.2
160404RH 0.4
160408RH 0.8
Boring
Bars
E66
E 11 Positive G Class
TPGR Grades Dimensions (mm)
T1500Z
T1000A
T1500A
ST10P
Inscribed circle
Thickness
Nose radius
W
Cat. No.
TPGR 110302R-W
6.35 3.18
0.2
110302L-W 0.2
110304R-W 0.4
110304L-W 0.4
110308L-W 0.8
TPGR 160302R-W
9.525 3.18
0.2
160302L-W 0.2
160304R-W 0.4
160304L-W 0.4
160308R-W 0.8
160308L-W 0.8
TPGN Grades Dimensions (mm)
AC510U
T1000A
T1500A
ST20E
A30
G10E
H1
NB90S
NB100C
Inscribed circle
Thickness
Nose radius
Cat. No.
TPGN 110302
6.35 3.18
0.2
110304 0.4
110308 0.8
TPGN 160302
9.525 3.18
0.2
160304 0.4
160308 0.8
160312 1. 2
General Boring (Top Clamp Type)
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Grades
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Applicable inserts Clamps
Double ended
screws
Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
S12M-CTFP R/L1103-16 S12M-CTFP R/L11
16 12 11 150
8.0
17 6
TP 110 3
CCM5BSL/R
WB5-10 LH025
S16Q-CTFP R/L1103-20 S16Q-CTFP R/L11
20 16 15 180
10.0
18 4
S20R-CTFP R/L1103-25 S20R-CTFP R/L11
25 20 18 200
12.5
18 2
S25S-CTFP R/L1603-32 S25S-CTFP R/L16
32 25 23 250
16.0
38 2TP 1603
CCM8UL/R
WB8R/L-16T
LT27
Inserts (Coated carbide / Cermet / Carbide)
Stop Boring
S-CTFP
Steel 91°
5°
GAMF
LH
H
LF
DMIN Min.
machinable diameter
DCON
WF
SEC-Boring Bars
S-CTFP Type 91°
mark: To be replaced by new item (Please confirm stock availability)
11 Positive M Class
TPMR Grades Dimensions (mm)
T1500Z
T3000Z
T1000A
T1500A
Inscribed circle
Thickness
Nose radius
FK
Cat. No.
TPMR 110302N-FK
6.35 3.18
0.2
110304N-FK 0.4
110308N-FK 0.8
TPMR 160304N-FK
9.525 3.18
0.4
160308N-FK 0.8
160312N-FK 1. 2
TPMR Grades Dimensions (mm)
AC820P
AC8025P
AC830P
ST10P
Inscribed circle
Thickness
Nose radius
SF
Cat. No.
TPMR 110304N-SF 6.35 3.18 0.4
110308N-SF 0.8
TPMR 160304N-SF
9.525 3.18
0.4
160308N-SF 0.8
160312N-SF 1. 2
11 M Class
TPMR Grades Dimensions (mm)
AC820P
AC8025P
AC830P
Inscribed circle
Thickness
Nose radius
UJ
Cat. No.
TPMR 110304N-UJ 6.35 3.18 0.4
110308N-UJ 0.8
TPMR 160304N-UJ 9.525 3.18 0.4
160308N-UJ 0.8
TPMN Grades Dimensions (mm)
AC405K
AC415K
AC420K
AC510U
T1000A
T1500A
ST10P
ST20E
A30
G10E
Inscribed circle
Thickness
Nose radius
Cat. No.
TPMN 110304 6.35 3.18 0.4
110308 0.8
TPMN 160304
9.525 3.18
0.4
160308 0.8
160312 1. 2
You can also use the 11 inserts with holes on page E61 to E65.
This figure shows right handed tools.
Dimensions (mm)
Boring
Bars
E67
E
11 Positiv e G Class
SUMIBORON
TPGN Grades Dimensions (mm)
BNX20
BN2000
BN500
BN7000
BN700
Inscribed circle
Thickness
Nose radius
Cat. No.
TPGN 110304
6.35 3.18
0.4
110308 0.8
TPGN 110304HS 0.4
110308HS 0.8
TPGN 160304
9.525 3.18
0.4
160308 0.8
TPGN 160304HS 0.4
160308HS 0.8
Note: The part number suffixes stand for the following: HS: Strengthened cutting edge type
11 Positive M Class
SUMIBORON One Use Inserts
(
mark: Only packages containing one piece are in stock,
mark: Packages containing one piece and packages containing 10 pieces are in stock)
NU-
TPGN
Grades Dimensions (mm)
BNX20
BN1000
BN2000
BN350
BN500
BN7000
BN700
Inscribed circle
Thickness
Nose radius
Cat. No.
NU-TPGN 110302
6.35 3.18
0.2
110304 0.4
110308 0.8
110302LT 0.2
110304LT 0.4
110308LT 0.8
110304HS 0.4
110308HS 0.8
NU-TPGN 160302
9.525 3.18
0.2
160304 0.4
160308 0.8
160304LT 0.4
160308LT 0.8
160304HS 0.4
160308HS 0.8
Note:
The part number suffixes stand for the following: LT: Cutting performance focused type
HS: Strengthened cutting edge type
SEC-Boring Bars
CTFP Type
mark: To be replaced by new item (Please confirm stock availability)
11 Positive G Class
SUMIDIA NF Inserts
NF-
TPGN
Grades Dimensions (mm)
DA1000
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
NF-TPGN 110302
6.35 3.18
0.2
110304 0.4
110308 0.8
NF-TPGN 160302
9.525 3.18
0.2
160304 0.4
160308 0.8
NF-
TPGN
Grades Dimensions (mm)
DA1000
DA2200
Inscribed circle
Thickness
Nose radius
Cat. No.
NF-TPGN 110304P 6.35 3.18 0.4
110308P 0.8
NF-TPGN 160304P 9.525 3.18 0.4
TPGN Grades Dimensions (mm)
DA150
Inscribed circle
Thickness
Nose radius
Cat. No.
TPGN 110302
6.35 3.18
0.2
110304 0.4
110308 0.8
TPGN 160302
9.525 3.18
0.2
160304 0.4
160308 0.8
Inserts ( SUMIBORON / SUMIDIA)
11 Positive M Class
SUMIDIA Break Master
NU-
TPMR
Grades Dimensions (mm)
DA150
Inscribed circle
Thickness
Nose radius
DM
Cat. No.
NU-TPMR 110302L-DM 6.35 3.18 0.2
110304L-DM 0.4
NU-TPMR 160302L-DM 9.525 3.18 0.2
160304L-DM 0.4
You can also use the 11° inserts with holes on page E61 to E65.
Boring
Bars
E68
E
General Boring
S-DTFN
Stop Boring
Steel
Fig 1 Fig 2
DCON
-10
WF
LF
LH
H
91°
-6°
DMIN Min.
machinable diameter
91°
-6°
DCON
GAMF
WF
LF H
DMIN Min.
machinable diameter
SEC-Boring Bars
S-DTFN Type / D-DTFN Type
91°
Oil hole
Steel with
vibration
control
mechanism
91°
– 6°
DCON
GAMF
WF
LF
LH
H
DMIN Min.
machinable diameter
Parts
Holders
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Applicable inserts
Clamp set
Shims
Screw for
shim
Wrench
for upper
surface
Wrench
for lower
surface
RL
DMIN
DCON
HLFWFLH
GAMF
Cat. No.
Page
Vibration control
mechanism
Steel with oil hole
D25T-DTFN R/L1604-32
32 25 23 300 17 21
12
TN 1604
From
B56
SCP-1 5.0
TNS1603B
BFTX0307N
LH040 LH025
D32T-DTFN R/L1604-40
40 32 30 300 22 26
10
TNS1604B
D40U-DTFN R/L1604-50
50 40 37 350 27 26
10
Parts
Holders
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height Length
Cutting edge
distance
Head
Fig Applicable inserts
Clamp set
Shim
Screw for shim
Wrench for
upper surface
Wrench for
lower surface
RL
DMIN
DCON
HLFWFLH Cat. No.
Page
Steel
S32S-DTFN R/L1604-40
40 32 30 250
22.0
26 1
TN 1604
From
B56
SCP-1 5.0
TNS1604B
BFTX0307N
LH040 LH025
S40T-DTFN R/L1604-50
50 40 37 300
27.0
26 1
S50U-DTFN R/L1604-63
63 50 47 350
31.5
2
TNMG160408N-GE
Inserts
D-DTFN
Stop Boring
Parts for clamp set
E81
Parts for clamp set
E81
Recommended tightning torque(N m) mark: Standard stocked item (expanded product)
This figure shows right handed tools.
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
Boring
Bars
E69
E
SEC-Boring Bars
S-PTFN Type / B-PTFN Type
General Boring
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat.
No.
Grades
Min. machining
diamete
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Fig
Applicable inserts
Lever
pins Bolts Shims
Shim
retainers
Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Cat. No.
Page
Steel
S25R-PTFN R/L1604-32
32 25 23 200
16.0 21.5
12
1
TN 1604
From
B56
LCL3 LCS3
LST317CA
LSP3 LH025
S32S-PTFN R/L1604-40
40 32 30 250
20.0 21.0
10
S32S-PTFN R/L1604-44
S32S-PTFN R/L16
44 32 30 250
22.0 21.0
10
S40T-PTFN R/L1604-50
50 40 37 300
25.0 21.0
10
S50U-PTFN R/L1604-63
63 50 47 350
31.5
10
2
S40T-PTFN R/L2204-54
S40T-PTFN R/L22
54 40 37 300
27.0 26.0
10
1
TN 2204
B61
LCL4 LCS4
LST42
LSP4 LH030
S50U-PTFN R/L2204-70
S50U-PTFN R/L22
70 50 47 350
35.0 33.0
10
S-PTFN
Stop Boring
Steel
Fig 1 Fig 2
DMIN Min.
machinable diameter
DCON
– 6°
GAMF
LH
H
WF
LF
91°
DCON
91°
– 6°
DMIN Min.
machinable diameter
GAMF
H
WF
LF
B-PTFN
Stop Boring
DMIN Min.
machinable diameter
91°
– 6°
DCON
GAMF
H
WF
LF
LH Parts
Holders
Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Cutting edge
distance
Head
Rake
angle Applicable inserts Lever
pin Bolt Shim Shim
retainer Wrench
RL
DMIN
DCON
HLFWFLH
GAMF
Cat. No.
Page
Steel with
vibration control
mechanism
B25T-PTFN R/L1604-32
32 25 23 300 16 21
12
TN 1604
From
B56
LCL3 LCS3
LST317CA
LSP3 LH025
B32U-PTFN R/L1604-40
40 32 30 350 20 21
10
B40W-PTFN R/L1604-50
50 40 37 450 25 21
10
Steel with
vibration
control
mechanism
TNMG160408N-GE
(Representative
example)
Inserts
91°
This figure shows right handed tools.
This figure shows right handed tools.
Dimensions (mm)
Dimensions (mm)
mark: Standard stocked item (expanded product)
Boring
Bars
E70
E
SEC- Boring Bars / SUMIBORON Small Diameter Boring Bars
S-ETFN Type / BNZ Type
91°
Inserts
TNMG160408N-GE
TNMG220408N-GE
(Representative example)
S-ETFN
Stop Boring
Steel
91°
– 6°
DCON
GAMF
WF
LF
LH
H
DMIN Min.
machinable diameter
Parts
Holders Right-handed (R) holders are applicable for left-handed (L) and neutral (N) inserts.
Left-handed (L) holders are applicable for right-handed (R) and neutral (N) inserts.
Holder
Material
Cat. No.
Conventional Cat. No.
Stock
Min.
machining
diameter
Diameter
Height
Length
Cutting
edge
distance
Head
Rake
angle
Applicable inserts
Shims
Eccentric shafts
Wrenches
RL
DMIN
DCON
HLFWFLH
GAMF
Cat. No. Page
Steel
S25R-ETFN R/L1604-34
BTFN325 R/L 34 25 23 200 17 18
12
TN 1604
From
B56 STW323 CPB34 LH025
S32S-ETFN R/L1604-44
BTFN332 R/L 44 32 30 250 22 20
10
CPB35
S40T-ETFN R/L2204-54
BTFN440 R/L 54 40 37 300 27 25
10
TN 2204
B61 STW434 CPB44T LH030
S50U-ETFN R/L2204-70
BTFN450 R/L 70 50 47 350 35 32
10
CPB45T
Dimensions (mm)
This figure shows right handed tools.
Boring
Bars
E71
E
SEC-Very Small Diameter Boring Bars
CKB Type
Characteristics
High index accuracy Swap inserts easily
Insert grades and applications
AC1030U: For stainless steel and general steel
ACZ150: For stainless steel and general steel
DA2200:
For alumnum alloys and non-ferrous alloys
Strong clamping due to
wedge effect
High index accuracy with
two contacting faces
Easy insert replacement by loosening a screw
High index accuracy
with 3-point protrusion
Offset amount 2 mm
(previous round shanks were 5–10 mm)
Wide chip pocket allows safe machining
to the bottom of the hole
Repertoire compatible with drill sleeves from various lathe manufacturers,
directly clampable (shank diameter ø19.05, 20.0, 22.0, 25.0, 25.4 mm)
Head is smaller than shank diameter,
allowing it to be inserted from the back side of the sleeve
ø1 mm to ø5 mm minimum machineable diameter in stock
Handles 20 mm maximum machineable depth (ø4, ø5 mm)
Compatible with various types of autolathes
High index accuracy through unique shape
Swap inserts easily
Round Shank Holders (Small Offset) [S-CKB-S Type]
Expanded machining range with offset amount of 2 mm
Boring
Bars
E72
E
Automotive Hydraulic Parts (SUS430)
Electronic Parts (Free-Cutting Stainless Steel)
Application Example
Application Example
Note: This figure shows the left handed right cutting edge.
Parts
Holders
Cat. No. Stock Height Width
Length
Depth of cut
Width Head Applicable insert Cat. No. Clamp
Double
ended screw
Wrench
H B LF CDX B2
HBKL
LH3
CKBS R1016-16-06 10 16 125 6 26 28.5 10 KBMX L0206- R
CKBW16 WB4-8 LH020
CKBS R1016-16-11 10 16 125 11 31 28.5 10 KBMX L03,04,0511- R
CKBS R1216-16-06 12 16 150 6 26 28.5 10 KBMX L0206- R
CKBS R1216-16-11 12 16 150 11 31 28.5 10 KBMX L03,04,0511- R
CKBS R1216-16-20 12 16 150 20 40 28.5 10 KBMX L04,0520- R
CKBS R1616-16-06 16 16 150 6 26 34.5 16 KBMX L0206- R
CKBS R1616-16-11 16 16 150 11 31 34.5 16 KBMX L03,04,0511- R
CKBS R1616-16-20 16 16 150 20 40 34.5 16 KBMX L04,0520- R
KBMX Type (for Very Small Diameter L Type Holders)
Cat. No.
AC1030U
ACZ310
Minimum
machineable diameter
Cutting edge
position
Offset
Nose radius
Length
Depth of cut
DMIN
WF3 E3 RE L CDX
KBMX L0206-05R 2.0 0.5 0.25 0.05 23.5 6
KBMX L0206-20R 0.20
KBMX L0311-05R 3.0 0.5 0.30 0.05 28.5 11
KBMX L0311-20R 0.20
KBMX L0411-05R
4.0 0.5 0.50
0.05 28.5 11
KBMX L0411-20R 0.20
KBMX L0420-05R 0.05 37.5 20
KBMX L0420-20R 0.20
KBMX L0511-05R
5.0 0.5 0.50
0.05 28.5 11
KBMX L0511-20R 0.20
KBMX L0520-05R 0.05 37.5 20
KBMX L0520-20R 0.20
Mini Boring L-Styled
Offset
0
CDX
HF
LH3
LF
HBKL
B
H
B2
16
(3.5) 6.5
5.5mm
ø2.5mm
ø10mm
19mm
ø4.0mm
CKBR1212-16
KBMXR 0420-05(ACZ310)
vc60m/min
f 0.01mm/rev
ap0.03mm
Water-insoluble cutting oil
Holder
Insert
Cutting speed
Feed rate
Depth of cut
Cutting fluid
CKBR1616
-
16
KBMXR 0206-05T(ACZ150)
vc80m/min
f 0.03mm/rev
ap0.05mm
Water-insoluble cutting oil
Holder
Insert
Cutting speed
Feed rate
Depth of cut
Cutting fluid
Inserts
SEC-Very Small Diameter Boring Bars
CKB Type
mark: Standard stocked item (expanded product) mark: To be replaced by new item (Please confirm stock availability)
H = HF (Cutting edge height)
Dimensions (mm)
Dimensions (mm)
20°
55°
DMIN Min.
machinable diameter
12.7
7. 0
6.2
WF3
E3
RE
CDX
L
10°
Boring
Bars
E73
E
SEC-Very Small Diameter Boring Bars
CKB Type
Parts
Holders
Cat. No. Stock Height Width Length
Cutting edge
distance
Cutting edge
height
Clamp
Double ended
screw
Wrench
H B L1 WF HF
CKB R1010-16 10 10 100 10 10
CKBW16 WB4-8 LH020
CKB R1212-16 12 12 125 12 12
CKB R1616-16 16 16 125 16 16
CKB R2020-16 20 20 125 20 20
CKB R2525-16 25 25 150 25 25
Parts
Holders
Cat. No. Stock
Diameter
Height Length
Cutting edge
distance
Clamp
Double ended
screw
Wrench
DCON H L1 WF
S1905H-CKB RS-16 19.05 17 100 2
CKBW16 WB4-8 LH020
S20H-CKB RS-16 20 18 100 2
S22K-CKB RS-16 22 19 125 2
S25K-CKB RS-16 25 23 125 2
S254K-CKB RS-16 25.4 23 125 2
Parts
Holders
Cat. No. Stock
Diameter
Height Length Length
Cutting edge
distance
Clamp
Double ended
screw
Wrench
DCON H L1 LS WF
S10F-CKB R-16 10 9 80 58 5
CKBW16 v-8 LH020
S12F-CKB R-16 12 11 80 58 6
S16H-CKB R-16 16 15 100 78 8
S19K-CKB R-16 19.05 17 125 103 8
S20K-CKB R-16 20 18 125 103 10
Square Shank
Round Shank (Offset Small)
Round Shank
20
L1
CDX
WF
BH
E3
HF
Center height
(On center)
20 L1
H
DCON
g6
H
CDX
WF
E3
See page E74 for the values of E3 and CDX.
22
WF
CDX
L1 LS H
H
E3
4
Center height
(On center)
DCON
g6
See page E74 for the values of E3 and CDX.
Dimensions (mm)
Dimensions (mm)
Dimensions (mm)
See page E74 for the values of E3 and CDX.
Boring
Bars
E74
E
KBMX Type and KBMX-T Type (For Internal Machining)
Cat. No.
AC1030U
ACZ310
Min. machining
diameter
Cutting edge
position
Offset
Nose radius
Length
Depth of cut
DMIN
WF3 E3 RE L CDX
KBMX R0103-05 1. 0 4.00 0.20 0.05 20.5 3
KBMX R0103-20 0.20
KBMX R01506-05 1. 5 4.05 0.25 0.05 23.5 6
KBMX R01506-20 0.20
KBMX R0206-05 2.0 4.05 0.25 0.05 23.5 6
KBMX R0206-20 0.20
KBMX R0311-05 3.0 4.10 0.30 0.05 28.5 11
KBMX R0311-20 0.20
KBMX R0411-05 4.0 4.30 0.50 0.05 28.5 11
KBMX R0411-20 0.20
KBMX R0420-05 4.0 4.30 0.50 0.05 37.5 20
KBMX R0420-20 0.20
KBMX R0511-05 5.0 4.50 0.70 0.05 28.5 11
KBMX R0511-20 0.20
KBMX R0520-05 5.0 4.50 0.70 0.05 37.5 20
KBMX R0520-20 0.20
Cat. No.
ACZ150
Min. machining
diameter
Cutting edge
position
Offset
Nose radius
Length
Depth of cut
DMIN
WF3 E3 RE L CDX
KBMX R0103-05T 1. 0 4.00 0.20 0.05 20.5 3
KBMX R0103-20T 0.20
KBMX R01506-05T 1. 5 4.05 0.25 0.05 23.5 6
KBMX R01506-20T 0.20
KBMX R0206-05T 2.0 4.05 0.25 0.05 23.5 6
KBMX R0206-20T 0.20
KBMX R0311-05T 3.0 4.10 0.30 0.05 28.5 11
KBMX R0311-20T 0.20
KBMX R0411-05T 4.0 4.30 0.50 0.05 28.5 11
KBMX R0411-20T 0.20
KBMX R0511-05T 5.0 4.50 0.70 0.05 28.5 11
KBMX R0511-20T 0.20
KBMZ Type (For Internal Turning)
Cat. No.
AC1030U
ACZ310
Min. machining
diameter
Cutting edge
position
Offset
Nose radius
Length Depth of cut
DMIN
WF3 E3 RE L CDX
CDX2
KBMZ R0411-05 4.0 5.10 1.3 0.05 28.5 9 11
KBMZ R0411-20 0.20
KBMZ R0511-05 5.0 5.10 1.3 0.05 28.5 9 11
KBMZ R0511-20 0.20
KBMG Type (For Internal Grooving)
Cat. No.
AC1030U
ACZ310
Min. machining
diameter
Cutting edge
position
Offset
Width of cut
Nose radius
Length
Depth of cut
DMIN
WF3 E3 CW RE L CDX
KBMG R0411-05 4.0 4.90 1.1 1.0 0.05 28.5 11
KBMG R0411-10 2.0 0.10
KBMG R0511-05 5.0 5.10 1.3 1.0 0.05 28.5 11
KBMG R0511-10 2.0 0.10
KBMF Type (For Face Grooving)
Cat. No.
ACZ150
Min. machining
diameter
Cutting edge
position
Offset
Width of cut
Nose radius
Length
Maximum
groove
depth
(mm)
DMIN
WF3 E3 CW RE L
KBMF R0615-05 6.0 4.0 0.2 1.5 0.05 21.8 4.0
KBMF R0620-05 6.0 4.0 0.2 2.0 0.05 21.8 4.0
KBMF R0630-05 6.0 4.0 0.2 3.0 0.05 21.8 4.0
KBMX Type (SUMIDIA / For Internal Machining)
Cat. No.
DA2200
Min. machining
diameter
Cutting edge
position
Offset
Nose radius
Length
Depth of cut
DMIN
WF3 E3 RE L CDX
KBMX R0311-10 3.0 4.1 0.3 0.1 28.5 11
KBMX R0411-10 4.0 4.3 0.5 0.1 28.5 11
KBMX R0511-10 5.0 4.5 0.7 0.1 28.5 11
KBMZ Type (For Internal Turning)
3.8
5°
15°
6.2
7. 0
55°
12.7
2
R0.25 R0.25
e0.3
WF3
E3
RE
CDX2
CDX
L
DMIN Min.
machinable diameter
Magnified diagram of cutting edge
(for minimum machinable diameter 4.0 mm)
Magnified diagram of cutting edge
(for minimum machinable diameter 4.0 mm)
Magnified diagram of cutting edge
(for minimum machinable
diameter 5.0 mm)
Magnified diagram of cutting edge
(for minimum machinable
diameter 5.0 mm)
KBMG Type (For Internal Grooving)
3.8
6.2
7. 0
55°
12.7
e
R0.25
WF3
E3
RE
RE
CDX
L
CW
CW
DMIN Min.
machinable diameter
Cutting edge Enlarged view of cutting edge
KBMF Type (For Face Grooving)
DMIN Min.
machinable diameter
3.8
4.3
5.3
6.2
7. 0
55°
12.7
WF3
E3
CW
RE
RE L
KBMX Type (SUMIDIA / For Internal Machining)
3.8
6.2
15°
7. 0
55°
12.7
15°
DMIN Min.
machinable diameter
WF3
E3
RE
CDX
L
KBMX Type, KBMX-T Type (For Internal Machining)
3.8
10°
20°
6.2
7. 0
55°
12.7
WF3
E3
RE
CDX
L
DMIN Min.
machinable diameter
KBMX Type KBMX-T Type
Reduces chip curl and evacuates
chips.
Type that evacuates chips towards
the back. Low cutting force
prevents chatter.
Inserts
SEC-Very Small Diameter Boring Bars
CKB Type
mark: Standard stocked item (expanded product) mark: To be replaced by new item (Please confirm stock availability)
Dimensions (mm)
Dimensions (mm)
Dimensions (mm)
Dimensions (mm)
Dimensions (mm)
Boring
Bars
E75
E
Carbide Solid Bars
BXBR Type
Characteristics
Tools
Cat. No. Grades
Minimum machineable
diameter*
Diameter
Height Length
Cutting edge
distance
Head
Depth of cut
Offset
Nose radius
Applicable Sleeves
ACZ150
AC530U
DMIN DCON H LF WF LH CDX E1 RE
With chipbreaker
BXBR 02005R 2.0 2.0 1.8 50 0.80 6.0 10.0 0.20 0.05 HBX 2016
BXBR 02020R 2.0 2.0 1.8 50 0.80 6.0 10.0 0.20 0.20 HBX 2016
BXBR 02505R 2.5 2.5 2.2 50 1.05 7.5 12.5 0.20 0.05 HBX 2516
BXBR 02520R 2.5 2.5 2.2 50 1.05 7.5 12.5 0.20 0.20 HBX 2516
BXBR 03005R 3.0 3.0 2.7 50 1.30 9.0 15.0 0.25 0.05 HBX 3016
BXBR 03020R 3.0 3.0 2.7 50 1.30 9.0 15.0 0.25 0.20 HBX 3016
BXBR 03505R 3.5 3.5 3.1 60 1.55 10.5 17.5 0.25 0.05 HBX 3516
BXBR 03520R 3.5 3.5 3.1 60 1.55 10.5 17.5 0.25 0.20 HBX 3516
BXBR 04005R 4.0 4.0 3.6 60 1.80 12.0 20.0 0.35 0.05 HBX 4016
BXBR 04020R 4.0 4.0 3.6 60 1.80 12.0 20.0 0.35 0.20 HBX 4016
BXBR 04505R 4.5 4.5 4.1 70 2.05 13.5 22.5 0.35 0.05 HBX 4516
BXBR 04520R 4.5 4.5 4.1 70 2.05 13.5 22.5 0.35 0.20 HBX 4516
BXBR 05005R 5.0 5.0 4.5 70 2.30 15.0 25.0 0.40 0.05 HBX 5016
BXBR 05020R 5.0 5.0 4.5 70 2.30 15.0 25.0 0.40 0.20 HBX 5016
Without chipbreaker
BXBR 02005R-NB 2.0 2.0 1.8 50 0.80 6.0 10.0 0.20 0.05 HBX 2016
BXBR 02020R-NB 2.0 2.0 1.8 50 0.80 6.0 10.0 0.20 0.20 HBX 2016
BXBR 02505R-NB 2.5 2.5 2.2 50 1.05 7.5 12.5 0.20 0.05 HBX 2516
BXBR 02520R-NB 2.5 2.5 2.2 50 1.05 7.5 12.5 0.20 0.20 HBX 2516
BXBR 03005R-NB 3.0 3.0 2.7 50 1.30 9.0 15.0 0.25 0.05 HBX 3016
BXBR 03020R-NB 3.0 3.0 2.7 50 1.30 9.0 15.0 0.25 0.20 HBX 3016
BXBR 03505R-NB 3.5 3.5 3.1 60 1.55 10.5 17.5 0.25 0.05 HBX 3516
BXBR 03520R-NB 3.5 3.5 3.1 60 1.55 10.5 17.5 0.25 0.20 HBX 3516
BXBR 04005R-NB 4.0 4.0 3.6 60 1.80 12.0 20.0 0.35 0.05 HBX 4016
BXBR 04020R-NB 4.0 4.0 3.6 60 1.80 12.0 20.0 0.35 0.20 HBX 4016
BXBR 04505R-NB 4.5 4.5 4.1 70 2.05 13.5 22.5 0.35 0.05 HBX 4516
BXBR 04520R-NB 4.5 4.5 4.1 70 2.05 13.5 22.5 0.35 0.20 HBX 4516
BXBR 05005R-NB 5.0 5.0 4.5 70 2.30 15.0 25.0 0.40 0.05 HBX 5016
BXBR 05020R-NB 5.0 5.0 4.5 70 2.30 15.0 25.0 0.40 0.20 HBX 5016
* When machining depth is less than dimension CDX
BXBR
Stop and Through Boring
10°
20°
WF
RE
CDX
LH
LF
H
DCON
E1
Min. machinable diameter DMIN
0
Sleeves
Cat. No. Stock
Dimensions
(mm)
Applicable Tools
DCON
HBX 2016 2.0 BXBR 020 R(-NB)
HBX 2516 2.5 BXBR 025 R(-NB)
HBX 3016 3.0 BXBR 030 R(-NB)
HBX 3516 3.5 BXBR 035 R(-NB)
HBX 4016 4.0 BXBR 040 R(-NB)
HBX 4516 4.5 BXBR 045 R(-NB)
HBX 5016 5.0 BXBR 050 R(-NB)
BXBR type can be installed on HBB type sleeves. In addition, you may also use other
commercially available sleeves. Please refer to page E78 for details on the HBX type sleeve.
Parts (For Sleeve)
Screw Set screw Wrench Applicable
sleeves
BFTX0409N
3.4 BT06035T TRD15
HBX
Sleeve is sold separately.
(Diagram shows type with breaker)
(For Torx holes)
Recommended tightening torque (N·m)
Dimensions (mm)
Economical two corner design
Handles up to 5D (5 times shank diameter) machining depth
Able to arbitrarily set the amount of protrusion
Easy to select since shank size is equal to minimum
machineable diameter (lineup includes bars from ø2 mm to
ø5 mm in increments of 0.5 mm)
KBMX type is used for the cutting edge. Type without
chipbreaker is also in stock.
Small Hole Finishing
Boring
Bars
E76
E
SUMIBORON Small Diameter Boring Bars
BSME Type
Tools
Cat. No.
Grades
Min. machining
diameter
Diameter
Neck diameter
Length Cutting edge
distance
Depth of cut
Nose radius
Fig Applicable
sleeves
BN2000 DMIN DCON DN LF WF CDX RE
RL
BSME R/L25020D2S6 2.5 6.0 2.0 32.0 1.20 5.3 0.2
1
HBSM6020
BSME R/L25020D3S6 2.5 6.0 2.0 34.5 1.20 7.8 0.2
BSME R/L25020D4S6 2.5 6.0 2.0 37.0 1.20 10.3 0.2
BSME R/L30020D2S6 3.0 6.0 2.5 32.8 1.45 6.3 0.2
2
BSME R/L30020D3S6 3.0 6.0 2.5 35.8 1.45 9.3 0.2
BSME R/L30020D4S6 3.0 6.0 2.5 38.8 1.45 12.3 0.2
BSME R/L35020D2S6 3.5 6.0 3.0 33.5 1.70 7.3 0.2
BSME R/L35020D3S6 3.5 6.0 3.0 37.0 1.70 10.8 0.2
BSME R/L35020D4S6 3.5 6.0 3.0 40.5 1.70 14.3 0.2
BSME R/L40020D2S6 4.0 6.0 3.5 33.9 1.95 8.3 0.2
BSME R/L40020D3S6 4.0 6.0 3.5 37.9 1.95 12.3 0.2
BSME R/L40020D4S6 4.0 6.0 3.5 41.9 1.95 16.3 0.2
BSME R/L45020D2S6 4.5 6.0 4.0 35.0 2.20 9.3 0.2
BSME R/L45020D3S6 4.5 6.0 4.0 39.5 2.20 13.8 0.2
BSME R/L45020D4S6 4.5 6.0 4.0 44.0 2.20 18.3 0.2
BSME R/L50020D2S6 5.0 6.0 4.5 35.8 2.45 10.3 0.2
BSME R/L50020D3S6 5.0 6.0 4.5 40.8 2.45 15.3 0.2
BSME R/L50020D4S6 5.0 6.0 4.5 45.8 2.45 20.3 0.2
BSME type requires separately sold sleeve HBSM6020.
SUMIBORON
BSME
Internal / Facing
Sleeves
ø20 DCB
LF
Cat. No. Stock Dia. Length Set screw Wrench
DCB LF
HBSM6020 6.0 80 BT0506 TH025
Sleeve is sold separately.
Alignment Jig*
Cat. No. Stock
AFBSM60
Characteristics
Fig 1 Fig 2
DMIN Min. machinable diameter DMIN Min. machinable diameter
10°
RE CDX CDX
LF LF
WF
RE
WF
DCON
DN
DCON
10°
DN
High precision cutting edge positioning is achieved
through a combination of tool/holder with taper on the
rear end, and a sleeve with an internal positioning pin.
(Common to BSME Type / SEXC Type)
Set screw
Sleeve
Tool / Holder
Positioning pin
Back end taper face
Newly Developed Clamp Mechanism
*
This is a jig for centering the sleeve when installing the sleeve into the sleeve holder.
Dimensions (mm)
Dimensions (mm)
Achieves minimum machineable diameter of ø2.5 mm for
hardened steel internal machining
Achieves high precision cutting edge positioning through
newly developed clamp mechanism
Achieves high performance machining comparable to grinding
machining with further cutting in the small hole region
Brazed type BSME type handles machining diameters
from ø2.5 mm up to ø5.0 mm
Indexable insert type SEXC type handles machining
diameters from ø4.0 mm up to ø6.0 mm
Boring
Bars
E77
E
SUMIBORON Small Diameter Boring Bars
SEXC Type
SUMIBORON
SEXC
Internal / Facing
Sleeves
ø20 DCB
LF
Cat. No. Stock Bore dia. Length Set screw Wrench
DCB LF
HBSM6020 6.0 80 BT0506 TH025
Sleeve is sold separately.
Inserts
75°
ø3.31
RE
7°
1. 1 5
Cat. No.
Grades
Dimensions
(mm)
BN2000
BN7000
Nose
radius
RE
2NU-ECXA 030X02LE
0.2
2NU-ECXA 030X02LF
0.2
The part number suffixes stand for the following:
LE: With honing LF: Sharp edge
Alignment Jig*
Cat. No. Stock
AFBSM60
Recommended Cutting Conditions
Main axis
rotation speed
n
Over 2,000 min-1
Low speed machining may cause
chattering and cutting edge chipping
Depth of cut
ap0.01–0.15 mm
Extreme depths of cut may cause
tool bending and degraded
accuracy of dimensions.
Feed rate
f0.01–0.10 mm/rev
DMIN Min. machinable diameter
10°
WF
DCON
CDX
LF
GAMF
DN
2.0 3.0 4.0 5.0 6.0
Machining diameter (mm)
Machining
accuracy
Good
SEXC Type
Indexable insert type
BSME Type
Brazed type
0 500 1,000 1,500 2,000
BSME
BSME
ø5.0
SEXC
SEXC
0 500 1,000 1,500
ø4.0
Cutting conditions v
c
135m/min 7,500min-1 f=0.02mm/rev a
p
=0.10mm Dry Cutting conditions v
c
50m/min 4,000min-1 f=0.02mm/rev a
p
=0.02mm Wet
Work material: Hardened steel alloy valve part (automotive related)
Tools: BSME R50020D2S6 Grade: BN2000
Work material: Bearing steel small automotive part (60HRC)
Holder: E06D2-SEXC R/L03-04P Insert: 2NU-ECXA 030X02LF(BN2000)
BSME type demonstrates extended life of over two times the life of CBN tools
from our competitors and achieves stable machining.
Competitor
CBN tools
Machining number (count)
Hardened steel alloy valve component
SEXC type achieves 1.5 times extended life compared with brazed CBN tools
from our competitors, and achieves greatly reduced tooling costs.
Bearing steel small automotive component
Indexable insert typeBrazed type
Competitor s brazed
CBN tools
Machining number (count)
600
1,700
1,000
1,500
Application Ranges
Application Examples
Parts
Holders
Cat. No. Stock
Min. machining
diameter
Diameter
Neck
diameter Length
Cutting edge
distance
Depth of cut
Rake
angle Applicable
sleeve
Clamp
bolts Wrench
RL
DMIN
DCON
DN LF WF CDX
GAMF
E06D2-SEXC R/L03-04P 4.0 6.0 3.75 33.75 1.95 8
13
HBSM6020
MIB1.6-2
0.2 SDBSM
E06D3-SEXC R/L03-04P 4.0 6.0 3.75 37.75 1.95 12
13
E06D2-SEXC R/L03-05P 5.0 6.0 4.75 35.25 2.45 10
12 MIB1.6-2.5
E06D3-SEXC R/L03-05P 5.0 6.0 4.75 40.25 2.45 15
12
E06D2-SEXC R/L03-06P 6.0 6.0 5.75 36.75 2.95 12
11
MIB1.6-3
E06D3-SEXC R/L03-06P 6.0 6.0 5.75 42.75 2.95 18
11
SEXC type requires separately sold sleeve HBSM6020.
*
This is a jig for centering the sleeve when installing the sleeve into the sleeve holder.
Recommended tightening torque (N·m)
Dimensions (mm)
Dimensions (mm)
Boring
Bars
E78
E
SUMIBORON
Holders
Cat. No. Grades
Min. machining
diameter
Diameter
Height
Length
Nose
radius Applicable
Sleeves
BN2000 BN7000
BN700
DMIN
DCON
HLFRE
Min. machinable diameter DMIN
3°
RE LF
H
DCON
BNBX 020R 2.5 2.0 1.8 40 0.2 HBX 2016
BNBX 025R 3.0 2.5 2.2 40 0.2 HBX 2516
BNBX 030R 3.5 3.0 2.7 40 0.2 HBX 3016
BNBX 035R 4.0 3.5 3.2 40 0.2 HBX 3516
BNBX 040R 4.5 4.0 3.7 40 0.2 HBX 4016
BNBX 045R 5.0 4.5 4.2 40 0.2 HBX 4516
BNBX 050R 5.5 5.0 4.7 60 0.2 HBX 5016
BNBX 055R 6.0 5.5 5.2 60 0.2 HBX 5516
BNBX 060R 6.5 6.0 5.7 60 0.2 HBX 6016
BNBX 065R 7. 0 6.5 6.2 60 0.2 HBB 6516
BNBX 070R 7. 5 7.0 6.7 80 0.2 HBB 716
BNBX 075R 8.0 7.5 7.2 80 0.2 HBB 7516
BNBX 080R 8.5 8.0 7.7 80 0.2 HBB 816
Sleeves
Cat. No. Stock
Hole
Diameter Applicable Tools
DCB
ø16
100
DCB
1515
HBX 2016 2.0 BNBX 020R
HBX 2516 2.5 BNBX 025R
HBX 3016 3.0 BNBX 030R
HBX 3516 3.5 BNBX 035R
HBX 4016 4.0 BNBX 040R
HBX 4516 4.5 BNBX 045R
HBX 5016 5.0 BNBX 050R
HBX 5516 5.5 BNBX 055R
HBX 6016 6.0 BNBX 060R
ø16
15
DCB
100
HBB 6516 6.5 BNBX 065R
HBB 716 7.0 BNBX 070R
HBB 7516 7.5 BNBX 075R
HBB 816 8.0 BNBX 080R
Note: BNBX type tools may also be installed in HBB type sleeves, but HBX type sleeves are recommended for tools with diameters less than ø6 mm.
Parts
Holders
Cat. No. Stock
Min. machining
diameter
Diameter Height Length
Rake angle
Clamp Bolts Nuts Wrench
DMIN DCON H LF GAMF
BNB 508R 10.0 8.0 7.0 140 9
BNBC
BH0306 BNBW-2
TH020
BNB 510R 12.0 10.0 9.0 140 8
FBUP3-A0-9
BNBW-4
BNB 512R 14.0 12.0 11.0 160 6
BNB 516R 18.0 16.0 14.0 180 5
BNB 520R 22.0 20.0 18.0 180 4BH0310 BNBW-7
Inserts (SUMIBORON, SUMIDIA)
ø3.97
60° 1.59
5°
5°
Grades
Dimensions
(mm)
SUMIBORON SUMIDIA
Nose radius RE
BNX10
BNX20
BN2000
BN350
BN500
BN7000
BN700
DA150
DA1000
Cat. No.
TBGN 060102B 0.2
TBGN 060104B 0.4
TBGN 060108B 0.8
TBGN 060102-BSTN*1 0.2
TBGN 060104-BSTN*1 0.4
TBGN 060108-BSTN*1 0.8
NF-TBGN 060102*2 0.2
NF-TBGN 060104*2 0.4
*1
TBGN -BSTN is an item
limited to BNX20 with
different negative land angle.
(BSTN: -15 , B: -25 )
Note that the negative
land angle is set
differently for each grade.
*2
NF-TBGN is a 1-corner design.
(All surfaces are not
SUMIDIA)
BNBX
Internal / Facing
Parts (For Sleeve)
Screw Set screws Wrenches Applicable
sleeves
BFTX0409N
1. 5
BT06035T TRD15
HBX2
3.0
HBX3
HBX4
HBX5
HBX6
BT0404 TH020
HBB
BNB
Internal / Facing
2°
DMIN Min.
machinable diameter
GAMF
LF H
DCON
SUMIBORON Small Diameter Boring Bars
BNBX Type / BNB Type
92˚
(For Torx
holes)
TRDBT06035T
BT0404
TH
Recommended tightning torque (N m) mark: To be replaced by new item (Please confirm stock availability)
Dimensions (mm)
Dimensions (mm)
This figure shows right
handed tools.
Boring
Bars
E79
E
SUMIBORON
Inserts (SUMIBORON)
80°
ø4.76
1.59
7°
Cat. No.
Grades
Dimensions
(mm)
BNC2010
BNC2020
BN1000
BN2000
BN7000
BN700
Nose
radius
RE
Package
contains
1 pc.
NU-ZNEX 040102 0.2
NU-ZNEX 040104 0.4
Package
contains
1 pc.
NC-ZNEX 040102LE 0.2
NC-ZNEX 040104LE 0.4
Package
contains
1 pc.
NC-ZNEX 040102LT 0.2
NC-ZNEX 040104LT 0.4
Package
contains
10 pcs.
T-NU-ZNEX 040102 0.2
T-NU-ZNEX 040104 0.4
BNZ
Internal / Facing
5°
DCON
GAMF LF H
DMIN Min.
machinable diameter
ø16
15 100
DCB Sleeves Stock
Hole diameter
DCB
Applicable holders
HBB 616 6
BNZ 606R
HBB 816 8
BNZ 608R
SUMIBORON Small Diameter Boring Bars
BNZ Type
91°
Parts
Holders
Cat. No. Stock
Min. machining
diameter
Diameter
Height
Length
Rake angle
Screw Wrench Sleeves
DMIN
DCON
HLF
GAMF
BNZ 606R
7. 0 6.0 5.5 80 14
BFTX0204N
0.5 TRX06
HBB 616
BNZ 608R
9.0 8.0 7.5 100 12 HBB 816
BNZ 610R
11.0 10.0 9.5 125 10
BNZ 612R
13.0 12.0 11.0 130 8
BNZ 616R
17.0 16.0 15.0 145 6
BNZ 620R
21.0 20.0 19.0 160 5
(For Torx holes)
Recommended tightning torque (N m) mark: To be replaced by new item (Please confirm stock availability)
Dimensions (mm)
Boring
Bars
E80
E
SUMIDIA Small Diameter Boring Bars
DABB Type
SUMIDIA
Holders
Cat. No. Grades
Min. machining
diameter
Diameter
Height Length
Nose radius
Applicable sleeves
DA2200
DMIN DCON H LF RE
DABB 045BR 7. 0 4.5 4.0 80 0.1 HBB 4516
DABB 060BR 9.0 6.0 5.5 80 0.1 HBB 616
Holders
Cat. No. Grades
Min. machining
diameter
Diameter
Height Length
Nose radius
Applicable sleeves
DA2200
DMIN DCON H LF RE
DABB 025NR 3.0 2.5 2.2 60 0.1 HBB 2516
DABB 035NR 4.0 3.5 3.2 60 0.1 HBB 3516
DABB 045NR 5.0 4.5 4.1 80 0.1 HBB 4516
DABB 060NR 7. 0 6.0 5.2 80 0.1 HBB 616
Holders
DABB-C
Stop & Through Boring
and Back Chamfer
Min. machinable
diameter DMIN
5°
50° RE
LF
H
DCON
DABB-N
Stop & Through Boring
and Necking
Min. machinable
diameter DMIN
25°
25° RE
LF
H
DCON
DABB-B
Back Turning
Min. machinable
diameter DMIN
10°
RE H
DCON
LF
Cat. No. Grades
Min. machining
diameter
Diameter
Height Length
Nose radius
Applicable sleeves
DA2200
DMIN DCON H LF RE
DABB 025CR 3.0 2.5 2.2 60 0.1 HBB 2516
DABB 035CR 4.0 3.5 3.2 60 0.1 HBB 3516
DABB 045CR 5.0 4.5 4.1 80 0.1 HBB 4516
DABB 060CR 7. 0 6.0 5.2 80 0.1 HBB 616
Sleeves
Parts
ø16
15 100
DCON
Cat. No. Stock
Dia.
DCON
(mm)
Set screw Wrench
HBB 2516 2.5
BT 0404 TH 020
HBB 3516 3.5
HBB 4516 4.5
HBB 616 6.0
mark: To be replaced by new item (Please confirm stock availability)
Dimensions (mm)
Dimensions (mm)
Dimensions (mm)
Boring
Bars
E81
E
Double-Clamp Holders
Parts for Clamp Set
Parts
Applicable
clamp set
Cat. No.
Springs Cap screws
(May also be tightened from below the screw)
Cat. No. Stock Cat. No. Stock
SCP-1 CSP08 CP-M5-20-1
5.0
SCP-2 CSP08 CP-M5-20-1
SCP-3 CSP08 CP-M5-20-1
SCP-4 CSP25 CP-M5-20-1
SCP-5 CSP08 CP-M5-20-1
SCP-6 CSP12 CP-M8-25-1 6.0
Recommended tightening torque (N·m)
E82
